Toshiba GR200 Series - Page 1120

6F2S1914 (0.49)
GRL200 (Soft 033 & 037)
- 1097 -
Table 5.6-6 Settings of LEDs on the Function keys (Function ID: 240001)
Setting items
Range
Units
Contents
Default setting
value
F1
Input signal1
(Preferred Data ID)
-
Set a Data ID at the first input on F1
(No Assigned)
Input signal2
(Preferred Data ID)
-
Set a Data ID at the second input on F1.
(No Assigned)
Input signal3
(Preferred Data ID)
-
Set a Data ID at the third input on F1.
(No Assigned)
Input signal4
(Preferred Data ID)
-
Set a Data ID at the forth input on F1.
(No Assigned)
Input signal5
(Preferred Data ID)
-
Set a Data ID at the fifth input on F1.
(No Assigned)
Input signal6
(Preferred Data ID)
-
Set a Data ID at the sixth input on F1.
(No Assigned)
Input signal7
(Preferred Data ID)
-
Set a Data ID at the seventh input on F1.
(No Assigned)
Input signal8
(Preferred Data ID)
-
Set a Data ID at the eighth input on F1.
(No Assigned)
Reset signal
(Preferred Data ID)
-
Setting Data ID for "Latch" circuit
(No Assigned)
LOGIC-SW
AND / OR / XOR
-
Switch for logic-gate operation on F1
AND
INVERSE-SW
Normal / Inverse
-
Inversion operation of F1 signal
Normal
TIMER-SW
Off/Delay/Dwell/Latch/Blink
-
Selection of a type in the delay timer on F1
Off
On Delay Timer
0.00 – 300.00
s
Set a value for an on-delay-timer on F1
0.00
Off Delay Timer
0.00 – 300.00
s
Set a value for an off-delay-timer on F1
0.00
Logic Timer
0.00 – 300.00
s
Off delay timer value for "Delay" and "Dwell" circuit
0.00
F2
Input signal1
(Preferred Data ID)
-
Set a Data ID at the first input on F2
(No Assigned)
Input signal2
(Preferred Data ID)
-
Set a Data ID at the second input on F2.
(No Assigned)
Input signal3
(Preferred Data ID)
-
Set a Data ID at the third input on F2.
(No Assigned)
Input signal4
(Preferred Data ID)
-
Set a Data ID at the forth input on F2.
(No Assigned)
Input signal5
(Preferred Data ID)
-
Set a Data ID at the fifth input on F2.
(No Assigned)
Input signal6
(Preferred Data ID)
-
Set a Data ID at the sixth input on F2.
(No Assigned)
Input signal7
(Preferred Data ID)
-
Set a Data ID at the seventh input on F2.
(No Assigned)
Input signal8
(Preferred Data ID)
-
Set a Data ID at the eighth input on F2.
(No Assigned)
Reset signal
(Preferred Data ID)
-
Setting Data ID for "Latch" circuit
(No Assigned)
LOGIC-SW
AND / OR / XOR
-
Switch for logic-gate operation on F2
AND
INVERSE-SW
Normal / Inverse
-
Inversion operation of F2 signal
Normal
TIMER-SW
Off/Delay/Dwell/Latch/Blink
-
Selection of a type in the delay timer on F2
Off
On Delay Timer
0.00 – 300.00
s
Set a value for an on-delay-timer on F2
0.00
Off Delay Timer
0.00 – 300.00
s
Set a value for an off-delay-timer on F2
0.00
Logic Timer
0.00 – 300.00
s
Off delay timer value for "Delay" and "Dwell" circuit
0.00
……….
F7
Input signal1
(Preferred Data ID)
-
Set a Data ID at the first input on F7
(No Assigned)
Input signal2
(Preferred Data ID)
-
Set a Data ID at the second input on F7.
(No Assigned)
Input signal3
(Preferred Data ID)
-
Set a Data ID at the third input on F7.
(No Assigned)
Input signal4
(Preferred Data ID)
-
Set a Data ID at the forth input on F7.
(No Assigned)
Input signal5
(Preferred Data ID)
-
Set a Data ID at the fifth input on F7.
(No Assigned)
Input signal6
(Preferred Data ID)
-
Set a Data ID at the sixth input on F7.
(No Assigned)
Input signal7
(Preferred Data ID)
-
Set a Data ID at the seventh input on F7.
(No Assigned)
Input signal8
(Preferred Data ID)
-
Set a Data ID at the eighth input on F7.
(No Assigned)
Reset signal
(Preferred Data ID)
-
Setting Data ID for "Latch" circuit
(No Assigned)
LOGIC-SW
AND / OR / XOR
-
Switch for logic-gate operation on F7
AND
INVERSE-SW
Normal / Inverse
-
Inversion operation of F7 signal
Normal
TIMER-SW
Off/Delay/Dwell/Latch/Blink
-
Selection of a type in the delay timer on F7
Off
On Delay Timer
0.00 – 300.00
s
Set a value for an on-delay-timer on F7
0.00
Off Delay Timer
0.00 – 300.00
s
Set a value for an off-delay-timer on F7
0.00
Logic Timer
0.00 – 300.00
s
Off delay timer value for "Delay" and "Dwell" circuit
0.00