Toshiba GR200 Series - Page 960

6F2S1914 (0.49)
GRL200 (Soft 033 & 037)
- 937 -
TPOS01 function (Function ID: 513001)
Assign to BOs
Operate Cmd.
with ILK† condition
S
R
0.1 – 50.0 s
[TPOS01-CPW]
Operate Cmd.
without ILK† condition
Operate condition‡
[TPOS01-LGCTRCON]
Fixedlogic
Fixedlogic
[TPOS01-LGP2EXOT]
DEV01_CONTROL_REQ
Command “Remote-P2-Control”
513001_7004016D08
ILK† condition (“P2”) passed
TPOS1-P2
TPOS01IN_TMP_28
513001 810401EE57
User configurable condition
(PLC#3 connection point)
“TPOS01_P2EC_OK_CSF”
(513001 8004011E7F)
&
&
1≥
&
1≥
1≥
&
&
&
“TPOS01_P2EX_BO”
(513001 8204011DD3) §§
Input
Output
Operate logic in TPOS01
To BO connection
“TPOS01_P2EC_OK_CS”
(513001 8304011E82)
[TPOS01-PLSM]*
Fix
Var
Operation Failed
[TPOS01-RST]
ASEQ function§” is in progress
ASEQ_MULTI_SEL
“TPOS01_P2EC_OK_CSF”
(513001 8004011E7F)
“TPOS01_EX_FFL”
(513001 8604011E91) ‡‡
To “Wait for a command”
&
Detection of state-change in a device
&
TPOS01IN_TMP_38
513001 820401EE5E
User configurable condition
(PLC#2 connection point)
1≥
&
“TPOS01_EX_CMP”
(5130018004011E93)
Operation Completed
1.0s- 100.0s
0
t
Figure 4.9-29 Operate ‘P2-control’ from the remote-end in TPOS01
††
†Note: The ILK function can provide the operation criteria for “P2” control.
‡Note: An “operate condition” signal is generated in the operate-condition logic (Figure
4.9-44) when Fixlogic is set for scheme switch [TPOS01-LGCTRCON]. If an
alternative “operate-condition” signal is required, it can be programmed by the
user and used to replace the signal generated by the original operate-condition
logic. The alternative “operate-condition” can be connected to the above logic using
connection point #3 “User configurable condition” That is, set the scheme switch
[TPOS01-LGCTRCON] to PLC and use “TPOS01IN_TMP_28”.
§Note: The ASEQ function can provide sequential signals for automatic control.
*Note: The user can set the type of output signal. When Var is set for the scheme switch
[TPOS01-PLSM], the output period of the signal is defined by the setting
[TPOS01-CPW]. When Fix is set, the signal ceases when the 43S or an ES is
changed.
‡‡Note: The “Operate failed” signal is issued when the state-change is not detected until
after reaching the time set by the setting [TPOS01-RST].
§§Note: The signal “TPOS01-PIEX-BO” is issued when Fixlogic is set for scheme switch
[TPOS01-LGP1EXOT]. The “operate-completed” signal can also be issued from
logic programmed by the user, in place of the logic shown in Figure 4.9-26. connect
the signal “operate completed” generated in the programmed logic to the