Toshiba GR200 Series - Page 1758

Rev. and
Date
Section
(page)
Change place and contents
Approved
by
Checked by
Prepared by
Chap. 6.3
Added the DCB operations
J. Nagata
Apr. 25
T. Utsumi
Apr 25
T. Kaneko
Apr. 18
Chap. 7.4.1
Added sample PLC logic for tele-protection
F. Kawano
May 16
K. Oohashi
May 15
T. Kaneko
May 15
Chap. 8.1 to
8.3
Added the setting lists for the ‘37’ software ordering in
the contents of Recording function
K. Oohashi
Apr 15
M. Oohashi
Apr 15
T. Kaneko
Apr. 12
Chap.10.2.33
Revised the information about Data(commslv) error
K. Oohashi
May 10
M. Okai
May 10
T. Kaneko
May 10
Chap.10.2.35
Revised the information about contact monitoring
K. Oohashi
May 11
N. Nagano
May 11
T. Kaneko
May 11
Chap. 11.4.9
Added Data ID list for the IEC 103 protocol
K. Oohashi
Apr 15
M. Oohashi
Apr 15
T. Kaneko
Apr. 12
Appendix 6
Corrected erroneous info for the selection of the
ordering in Ordering sheet
K. Oohashi
May 10
K. Oohashi
May 10
T. Kaneko
May 10
Appendix 6
Added the selection of PRP in the software selection of
the ordering
K. Kasuga
May 10
K. Kasuga
May 10
T. Kaneko
May 10
Appendix 6
Corrected typo for the SOFTSW function in FB table
K. Oohashi
May 10
M. Oohashi
May 10
T. Kaneko
May 10
Appendix 6
Modified the table of BIO code
K. Oohashi
May 10
M. Ueda
May 10
T. Kaneko
May 10
Appendix 7
Revised the information of BIO module terminal
structure in Compression terminal
K. Kasuga
May 10
K. Kasuga
May 10
T. Kaneko
May 10
Appendix 7
Revised the information about the RS485 interface for
serial rear port
K. Kasuga
May 10
K. Kasuga
May 10
T. Kaneko
May 10
Appendix 7
Added a CMP_NUM notice in Electromagnetic
Environment for the Environmental performance
F. Kawano
May 16
K.Oohashi
May. 16
T. Kaneko
May 16
0.14
May 23, 2016
Chap. 2.38
Added CLP function
K. Oohashi
May 23
N. Nagano
May 23
T. Kaneko
May 23
0.15
June27, 2016
Chap. 2.10
Corrected typo ‘Z1S-X.Reach’ to ‘Z1S-Mho.Reach’ in
Figure 2.10-18
K. Oohashi
June 1
T. Nakatsuka
June 1
T. Kaneko
June 1
Chap. 2.34
Added the calibration factor when the rating voltages
are different in VCHK
K. Oohashi
June 16
T. Nagano
Jun 16
T. Kaneko
Jun. 16
Chap. 4.1
Corrected the setting name for SPOS01_LGCNFFC in
the description above Fig 4.1-18
K. Oohashi
June 2
K. Oohashi
June 2
T. Kaneko
June. 2
Chap. 4.1
Corrected the wrong signal names in Fig. 4.1-18, -20, -
22, -24, -26
K. Oohashi
May 25
K. Oohashi
May 25
T. Kaneko
May 25
Chap. 4.3
Corrected the incorrect signal named in Fig. 4.3-4 SCB
logic
K. Oohashi
June 10
K. Oohashi
June 10
T. Kaneko
June 10
Chap.5.4.2(i)
Corrected Typo in the notice with regard to the contents
about the variable type in BI2 and BIO4
T.Sugamoto
June 15
T.Sugamoto
June 15
T. Kaneko
June 15
Chap. 12.9
Refined the contents about the information screen in
User interface
K. Oohashi
June 3
K. Oohashi
June 3
T. Kaneko
June 3
Chap. 13.5
Added the notice for attaching a support pillar for the
unit case
F. Yanazaki
June 15
F. Yanazaki
June 15
T. Kaneko
June 15
Appendix 6
Added the operation information to find the ordering
screen from the IED screen
K. Oohashi
June 3
K. Oohashi
June 3
T. Kaneko
June 3
Appendix 6
Added new code ‘4M’ in the ordering about the BIO
modules
K. Oohashi
Jun 1
M. Ueda
Jun 1
T. Kaneko
May 31
Appendix 6
Added the table for optional kits in the ordering
K. Oohashi
Jun 9
M. Ueda
Jun 9
T. Kaneko
Jun 9
Appendix 6
Deleted ‘3J’, ‘3Q’, ‘48’ codes of the BIO modules in the
ordering
K. Oohashi
Jun 21
M. Ueda
Jun 21
T. Kaneko
Jun 21
Appendix 6
Revised the selection table about serial ports in the
ordering and PRP protocol
F. Kawano
Jun 21
K. Oohashi
Jun 21
T. Kaneko
Jun 21
Appendix 6
Added CLP function in the function table for the 34 and
F. Kawano
K. Oohashi
T. Kaneko