Lenze E84AVHC Series - Page 818

8400 HighLine | Parameter setting & configuration
Parameter reference
Table of attributes
818 L Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010
C01151 L_PhaseIntK: Compare 23424 5B80 A 2 INTEGER_32 1 ;;
C01202
Axis data: iM motor/process 23373 5B4D A 2 UNSIGNED_16 1 ;;
C01203
Axis data: iG motor/position encoder 23372 5B4C A 2 UNSIGNED_16 1 ;;
C01204
Axis data: Feed constant 23371 5B4B E 1 INTEGER_32 10000 ;;
C01205
Axis data: Position resolution 23370 5B4A E 1 INTEGER_32 10000 ;
C01206
Axis data: Mounting direction 23369 5B49 A 2 UNSIGNED_8 1 ;;;
C01210
Axis data: Current positions 23365 5B45 A 6 INTEGER_32 10000 ;
C01211
Axis data: Speed 23364 5B44 A 1 INTEGER_32 10000 ;
C01213
MCK: Max. traversing distance 23362 5B42 A 1 INTEGER_32 1 ;
C01215
Axis data: Following error 23360 5B40 A 2 INTEGER_32 10000 ;;
C01216
MCK: Positioning setting 23359 5B3F E 1 UNSIGNED_8 ;;
C01218
MCK: PosFollower setting 23357 5B3D E 1 UNSIGNED_8 ;;
C01219
MCK: Speed follower setting 23356 5B3C E 1 UNSIGNED_8 ;;
C01221
MCK: Ref. mode 23354 5B3A E 1 UNSIGNED_8 1 ;;
C01222
MCK: Ref. M limit mode 14/15 23353 5B39 E 1 INTEGER_16 100 ;;
C01223
MCK: Ref. waiting time mode 14/15 23352 5B38 E 1 UNSIGNED_16 1 ;;
C01224
MCK: Ref. speeds 23351 5B37 A 2 INTEGER_32 10000 ;;
C01225
MCK: Ref. accelerations 23350 5B36 A 2 INTEGER_32 10000 ;;
C01226
MCK: Ref. S-ramp time 23349 5B35 A 1 UNSIGNED_16 1000 ;;
C01227
MCK: Ref. positions 23348 5B34 A 2 INTEGER_32 10000 ;;
C01228
MCK: Ref. sequence profile 23347 5B33 E 1 UNSIGNED_8 1 ;;
C01229
MCK: Position limiting values 23346 5B32 A 2 INTEGER_32 10000 ;;
C01230
MCK: Manual jog setting 23345 5B31 E 1 UNSIGNED_8 ;;
C01231
MCK: Manual jog speeds 23344 5B30 A 2 INTEGER_32 10000 ;;
C01232
MCK: Manual jog accelerations 23343 5B2F A 2 INTEGER_32 10000 ;;
C01233
MCK: Manual jog S-ramp time 23342 5B2E A 1 UNSIGNED_16 1000 ;;
C01234
MCK: Manual jog breakpoints 23341 5B2D A 4 INTEGER_32 10000 ;;
C01235
MCK: Manual jog waiting times 23340 5B2C A 1 UNSIGNED_16 1000 ;;
C01236
MCK: Follower speeds 23339 5B2B A 1 INTEGER_32 10000 ;;
C01237
MCK: Follower accelerations 23338 5B2A A 2 INTEGER_32 10000 ;;
C01238
MCK: Follower S-ramp times 23337 5B29 A 1 UNSIGNED_16 1000 ;;
C01239
MCK: Interpolator cycle - PosFollower 23336 5B28 E 1 UNSIGNED_32 1000 ;;
C01240
MCK: Control word 23335 5B27 E 1 UNSIGNED_32 ;
C01241
MCK: Status word 23334 5B26 E 1 UNSIGNED_32 ;
C01242
MCK: Current pos. profile no. 23333 5B25 E 1 UNSIGNED_8 1 ;
C01243
MCK: Current operating mode 23332 5B24 E 1 UNSIGNED_8 1 ;
C01244
MCK: Target detection - times 23331 5B23 A 1 UNSIGNED_16 1 ;;
C01245
MCK: Target detection - positions 23330 5B22 A 1 INTEGER_32 10000 ;;
C01251
MCK: Stop accelerations 23324 5B1C A 1 INTEGER_32 10000 ;;
C01252
MCK: Stop S-ramp times 23323 5B1B A 1 UNSIGNED_16 1000 ;;
C01295
L_MCKStateInterface_1: Position
selection
23280 5AF0 E 1 UNSIGNED_8 1 ;;
C01296
Mode for calculating the position 23279 5AEF A 2 UNSIGNED_8 1 ;;
C01297
Alternative function 23278 5AEE E 1 UNSIGNED_8 ;;
C01298
MCK: Change of operating mode with
profile no.
23277 5AED A 4 UNSIGNED_8 1 ;;
C01299
MCKI: MCKInterface status 23276 5AEC E 1 UNSIGNED_8 ;
C01300
Profile data: Positioning mode 23275 5AEB A 15 UNSIGNED_8 1 ;;
C01301
Profile data: Position 23274 5AEA A 15 INTEGER_32 10000 ;;
C01302
Profile data: Speed 23273 5AE9 A 15 INTEGER_32 10000 ;;
C01303
Profile data: Acceleration 23272 5AE8 A 15 INTEGER_32 10000 ;;
C01304
Profile data: Deceleration 23271 5AE7 A 15 INTEGER_32 10000 ;;
Code Name Index Data Access
dec hex DS DA DT Factor R w CINH
efesotomasyon.com - Lenze