Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010 L 475
8400 HighLine | Parameter setting & configuration
Diagnostics & error management
Error messages of the operating system
9.9.3 Short overview (A-Z)
The table below contains all error messages of the controller operating system in
alphabetical order.
Tip!
If you click the cross-reference in the first column, "Error number", you get to the
detailed description of the respective error message in the subsequent "Cause &
possible remedies" chapter . ( 478)
Note!
For the sake of legibility, the Logbookand C00165 display the error number with
the following syntax:
[Error type].[Error subject area no.].[Error ID]
In this documentation, "xx", a wildcard, stands for the error type since it is
configurable for many error messages.
Error number Error message Response
(Lenze setting)
can be set in CAN Emergency
Error Code
xx.0125.00001
An01: AIN1_I < 4 mA TroubleQuickstop C00598/1 0xF000
xx.0125.00002
An02: AIN2_I < 4 mA TroubleQuickstop C00598/2 0xF000
xx.0131.00006
CA06: CAN CRC error No response C00592/1 0x8000
xx.0131.00007
CA07: CAN Bus Warn No response C00592/3 0x8000
xx.0131.00008
CA08: CAN Bus Stopped No response C00592/4 0x8000
xx.0131.00011
CA0b: CAN HeartBeatEvent No response C00592/5 0x8130
xx.0131.00015
CA0F: CAN control word Fault C00594/2 0xF000
xx.0127.00002
CE04: MCI communication error No response C01501/1 0x7000
xx.0127.00015
CE0F: MCI control word Fault C00594/2 0xF000
xx.0135.00001
CE1: CAN RPDO1 No response C00593/1 0x8100
xx.0135.00002
CE2: CAN RPDO2 No response C00593/2 0x8100
xx.0135.00003
CE3: CAN RPDO3 No response C00593/3 0x8100
xx.0131.00000
CE4: CAN Bus Off No response C00592/2 0x8000
xx.0184.00001
Ck01: Pos. HW limit switch TroubleQuickstop C00595/1 0x8600
xx.0184.00002
Ck02: Neg. HW limit switch TroubleQuickstop C00595/2 0x8600
xx.0184.00007
Ck03: Pos. SW limit position TroubleQuickstop C00595/3 0x8600
xx.0184.00008
Ck04: Neg. SW limit position TroubleQuickstop C00595/4 0x8600
xx.0184.00153
Ck05: Error following error 1 Warning C00595/5 0x8611
xx.0184.00154
Ck06: Error following error 2 Warning C00595/6 0x8611
xx.0184.00155
Ck07: Travel range limit exceeded TroubleQuickstop C00595/7 0x8612
xx.0184.00156
Ck08: Home Position Unknown WarningLocked C00595/8 0x8612
xx.0184.08005
Ck09: Positioning mode invalid WarningLocked C00595/9 0x8600
xx.0184.08007
Ck10: Profile data implausible WarningLocked C00595/10 0x8600
xx.0184.08009
Ck11: Operating mode invalid Warning C00595/11 0x8600
xx.0184.08014
Ck12: Profile no. invalid WarningLocked C00595/12 0x8600
xx.0184.08015
Ck13: Error - MCKCtrlInterface Function Block Warning C00595/13 0x8600
xx.0184.00015
Ck14: Target position outside travel range limit WarningLocked C00595/14 0x8600
xx.0135.00004
CP04: CAN RPDO4 No response C00593/4 0x8100
xx.0145.00018
dF18: BU RCOM error Fault - 0x6100
xx.0145.00021
dF21: BU Watchdog Fault - 0x6100
efesotomasyon.com - Lenze
To Next Page
Loading...