Lenze E84AVHC Series - Page 1111

Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010 L 1111
8400 HighLine | Parameter setting & configuration
Index
LS_ParFree (C00471) 662
LS_ParFree_a 1082
LS_ParFree_a (C00472) 663
LS_ParFree_b 1083
LS_ParFree_b (C00470) 662
LS_ParFree_p 1084
LS_ParFree_p (C00474) 663
LS_ParFree_v 1085
LS_ParFree_v (C00473) 663
LS_ParReadWrite 1086
LS_ParReadWrite 1-6
Cycle time (C01091)
762
FailState (C01092) 762
LS_ParReadWrite_1 1086
LS_ParReadWrite_2 1086
LS_ParReadWrite_3 1086
LS_ParReadWrite_4 1086
LS_ParReadWrite_5 1086
LS_ParReadWrite_6 1086
LS_PulseGenerator 1088
LS_PulseGenerator (C00400) 649
LS_SetError_1 496
LS_SetError_2 498
LS_SetError_x
Error number (C00161)
617
LS_WriteParamList 1090
Error line (C01084) 760
Execute mode (C01082) 760
FailState (C01083) 760
Index (C01085) 760
WriteValue_1 (C01086) 761
WriteValue_2 (C01087) 761
WriteValue_3 (C01088) 761
WriteValue_4 (C01089) 761
LU
DC bus undervoltage (error message)
480
M
Machine parameters 385
Main program runtime (C00321) 636
Mains phase failure monitoring 205
Mains voltage (C00173) 623
Manual DC-injection braking (DCB) 175
Manual jog 406
Manual jog to software limit position 411
Master functionality (CAN) 515
Max. no. of AutoFailReset procedures (C00186) 626
Maximum current monitoring 205
Maximum torque (C00057) 598
Maximum torque monitoring 206
MCI input words (C00876) 748
MCI output words (C00877) 749
MCI_InOut
Inversion (C00890)
749
MCI1
Module missing/incompatible (error message)
488
MCK 361
Acceleration/deceleration times (C02610) 792
Act. pos. profile number (C01242) 780
Change of operating mode with profile no. (C01298)
783
Control word (C01240) 777
Current operating mode (C01243) 780
Follower accelerations (C01237) 776
Follower speeds (C01236) 776
Follower S-ramp times (C01238) 776
Interpolator cycle - PosFollower (C01239) 776
Limitations (C02611) 793
Manual jog accelerations (C01232) 774
Manual jog breakpoints (C01234) 775
Manual jog setting (C01230) 774
Manual jog speeds (C01231) 774
Manual jog S-ramp time (C01233) 775
Manual jog waiting times (C01235) 775
Max. distance to be traversed (C01213) 768
PosFollower setting (C01218) 770
Position limiting values (C01229) 773
Positioning setting (C01216) 769
Ref positions (C01227) 773
Ref speeds (C01224) 772
Ref. accelerations (C01225) 772
Ref. M limit mode 14/15 (C01222) 771
Ref. mode (C01221) 771
Ref. sequence profile (C01228) 773
Ref. S-ramp time (C01226) 772
Ref. waiting time mode 14/15 (C01223) 771
Resp. MCK error (C00595) 674
Speed follower setting (C01219) 770
Status word (C01241) 778
Stop accelerations (C01251) 781
Stop S-ramp times (C01252) 781
Target detection - positions (C01245) 781
Target detection - times (C01244) 780
MCK control word 369
MCK interface 374
MCK status word 371
MCKI
MCKInterface status (C01299)
783
MCTRL
Actual speed value (C00051)
597
Speed setpoint (C00050) 597
Min/max speed 389
Mode
Position calculation (C01296)
782
Moment of inertia (C00273) 634
Monitoring 197, 464
Motion Control Kernel (MCK) 361
Motor cable cross-section (C00916) 750
Motor cable length (C00915) 750
Motor cable resistance (C00917) 751
Motor catalogue 100
efesotomasyon.com - Lenze