Lenze E84AVHC Series - Page 1103

Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010 L 1103
8400 HighLine | Parameter setting & configuration
Index
C986 756
C987 756
C988 756
C99 605
C990 757
C991 757
C992 757
C993 757
C994 757
CA06
CAN CRC error (error message)
486
CA07
CAN bus warning (error message)
486
CA08
CAN bus stopped (error message)
487
CA0b
CAN HeartBeatEvent (error message)
487
CA0F
CAN control word (error message)
487
Calculating mass inertia (SC) 158
Calculating mass inertia (SLVC) 142
CAN baud rate (C00351) 643
CAN data telegram 509
CAN decoupling PDOInOut (C00342) 639
CAN DIP switch setting (C00349) 642
CAN error status (C00345) 641
CAN HeartBeat ConsumerTime (C00386) 649
CAN heartbeat producer time (C00381) 648
CAN IN/OUT COBID source (C00353) 643
CAN input words (C00866) 746
CAN Management
Error configuration (C00341)
638
CAN MessageError (C00364) 647
CAN monitoring times (C00357) 645
CAN node addr. HeartBeat producer (C00385) 649
CAN node address (C00350) 642
CAN on board 500
CAN output words (C00868) 747
CAN Rx PDOs transmission mode (C00323) 637
CAN slave/master (C00352) 643
CAN start remote node 515
CAN status (C00359) 646
CAN status HeartBeat producer (C00347) 641
CAN sync Rx identifier (C00367) 647
CAN sync transmission cycle time (C00369) 648
CAN sync Tx identifier (C00368) 647
CAN SyncTxRx times (C00370) 648
CAN telegram counter (C00360) 646
CAN time settings (C00356) 645
CAN_Tx_Rx_Error (C00372) 648
CAN1_OUT transmit at sync (C00366) 647
CANx_OUT data length (C00358) 645
CANxInOut
Inversion (C00401)
650
Cause of controller inhibit (C00158) 616
Cause of quick stop QSP (C00159) 617
CE04
MCI communication error (error message)
486
CE0F
MCI control word (error message)
486
CE1
CAN RPDO1 (error message)
487
CE2
CAN RPDO2 (error message)
487
CE3
CAN RPDO3 (error message)
488
CE4
CAN bus off (error message)
486
CAN RPDO4 (error message) 488
Checksums (C516) 666
Ck01
Pos. HW limit switch (error message)
491
Ck02
Neg. HW limit switch (error message)
491
Ck03
Pos. SW limit position (error message)
491
Ck04
Neg. SW limit position (error message)
491
Ck05
Following error 1 (error message)
492
Ck06
Following error 1 (error message)
492
Ck07
Travel range limit exceeded (error message)
492
Ck08
Home position unknown (error message)
492
Ck09
Positioning mode invalid (error message)
492
Ck10
Implausible profile data (error message)
492
Ck11
Invalid operating mode (error message)
493
Ck12
Invalid profile number (error message)
493
Ck13
Error - MCKCtrlInterface function block (error
message)
493
Ck14
Target position outside travel range limit (error
message)
491
COB-ID 509
COBID (C00354) 644
COB-ID EMCY (I-1014) 554
COB-ID SYNC message (I-1005) 553
Communication control words (C00136) 610
Communication cycle period (I-1006) 554
Communication time 504
Comparing applications 867
Comparing FB interconnections 867
efesotomasyon.com - Lenze