Lenze E84AVHC Series - Page 1113

Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010 L 1113
8400 HighLine | Parameter setting & configuration
Index
PartitionValue (C310) 636
Password1 (C304) 635
Password2 (C305) 635
PDO mapping 518, 519, 520
PDO synchronisation 527
Peak current limitation 109
Phase sequence reversal 181
Plant parameters 101
Port block "LP_CanIn1" 518
Port block "LP_CanIn2" 519
Port block "LP_CanIn3" 520
Port block "LP_CanOut1" 521
Port block "LP_CanOut2" 522
Port block "LP_CanOut3" 523
PosExecute (control bit) 381
PosExecute control bit 381
Position encoder selection (C00490) 665
Position follower 431
Position teaching 427
Positioning 414
Positioning modes 421
Power section ID (C00093) 604
Power-on time meter (C00179) 625
Pre-defined error field (I-1003) 552
Printing the interconnection 866
Process data objects, identifiers 524
Processing time 504
Producer heartbeat time (I-1017) 556
Product type code (C00203) 627
Production date (C206) 628
Profile data
Acceleration (C01303)
785
Deceleration (C01304) 785
Final speed (C01305) 785
Position (C01301) 784
Positioning mode (C01300) 784
Sequence profile (C01307) 786
Speed (C01302) 784
S-ramp time (C01306) 786
Profile entry 418
Profile linkage with velocity changeover (overchange)
420
PS01
No memory module (error message)
488
PS02
Par. set invalid (error message)
488
PS03
Par. set device invalid (error message)
489
PS04
Par. set Mci invalid (error message)
489
PS07
Par. memory module invalid (error message)
489
PS08
Par. device invalid (error message)
489
PS09
Par. format invalid (error message)
489
PTC 201
R
Ramp rounding main setpoint (C00134) 609
Rated brake resistor power (C00130) 609
Rated device current (C00098) 605
Rated motor current (C00088) 603
Rated motor frequency (C00089) 604
Rated motor power (C00081) 602
Rated motor speed (C00087) 603
Rated motor torque (C00097) 605
Rated motor voltage (C00090) 604
RCOM error counter (C290) 635
Reduced brake chopper threshold (C00174) 624
Reference project 871
Reference setting 395
Referencing mode 397
Reset of error message 474
Resp. LS_SetError_x (C00581) 671
Resp. to brake resist. overtemp. (C00574) 670
Resp. to CAN bus connection (C00592) 672
Resp. to CANx_IN monitoring (C00593) 673
Resp. to communication error with MCI (C01501) 786
Resp. to control word error (C00594) 673
Resp. to controller limitations (C00570) 669
Resp. to DC-bus voltage (C00600) 675
Resp. to device overload (Ixt) (C00604) 676
Resp. to earth fault (C00602) 676
Resp. to encoder wire breakage (C00586) 672
Resp. to fan failure (C00566) 668
Resp. to heatsink temp. > shutdown temp. -5°C
(C00582)
671
Resp. to high freq. DI12/67 reached (C00607) 676
Resp. to mains phase failure (C00565) 668
Resp. to max. speed / output freq. reached (C00579)
670
Resp. to max. speed at switch. freq. (C00588) 672
Resp. to maximum current (C00609) 677
Resp. to maximum torque (C00608) 676
Resp. to motor overload (I²xt) (C00606) 676
Resp. to motor overtemp. PTC (C00585) 671
Resp. to motor phase failure (C00597) 674
Resp. to open circuit AINx (C00598) 675
Resp. to peak current (C00569) 669
Resp. to speed controller limited (C00567) 669
Resp. to switching frequency reduction (C00590) 672
Resp. too frequent AutoFailReset (C00189) 626
Response for brake resistor control (C00175) 624
Retracting from limit switches 413
Reversing the phase sequence 181
RPDO1 communication parameter (I-1400) 560
RPDO1 mapping parameter (I-1600) 563
efesotomasyon.com - Lenze