Layer 2,3,IPv6+QoS Switch
_____________________________________________________________________________
Layer 2,3,IPv6+QoS Network Switch User Manual Version 0.1 Page: 841/970
for the selected port. The transmit period is the value, in seconds, of the timer used by the
authenticator state machine on the specified port to determine when to send an EAPOL
EAP Request/Identity frame to the supplicant. The transmit period must be a number in
the range of 1 to 65535. The default value is 30. Changing the value will not change the
configuration until the Submit button is pressed.
Guest VLAN Id (secs) - This field allows the user to configure Guest Vlan Id on the
interface. The valid range is 0 - L7_PLATFORM_MAX_VLAN_ID.The default value is 0.
Changing the value will not change the configuration until the Submit button is pressed.
Enter 0 to reset the Guest Vlan Id on the interface.
Guest VLAN Period (secs) - This input field allows the user to enter the guest Vlan period
for the selected port. The guest Vlan period is the value, in seconds, of the timer used by
the GuestVlan Authentication. The guest Vlan timeout must be a value in the range of 1
and 300. The default value is 90. Changing the value will not change the configuration until
the Submit button is pressed.
Supplicant Timeout (secs)- This input field allows the user to enter the supplicant
timeout for the selected port. The supplicant timeout is the value, in seconds, of the timer
used by the authenticator state machine on this port to timeout the supplicant. The
supplicant timeout must be a value in the range of 1 to 65535. The default value is 30.
Changing the value will not change the configuration until the Submit button is pressed.
Server Timeout (secs)- This input field allows the user to enter the server timeout for the
selected port. The server timeout is the value, in seconds, of the timer used by the
authenticator on this port to timeout the authentication server. The server timeout must be
a value in the range of 1 to 65535. The default value is 30. Changing the value will not
change the configuration until the Submit button is pressed.
Maximum Requests - This input field allows the user to enter the maximum requests for
the selected port. The maximum requests value is the maximum number of times the
authenticator state machine on this port will retransmit an EAPOL EAP Request/Identity
before timing out the supplicant. The maximum requests value must be in the range of 1 to
10. The default value is 2. Changing the value will not change the configuration until the
Submit button is pressed.
Reauthentication Period (secs)- This input field allows the user to enter the
reauthentication period for the selected port. The reauthentication period is the value, in
seconds, of the timer used by the authenticator state machine on this port to determine
when reauthentication of the supplicant takes place. The reauthentication period must be
a value in the range of 1 to 65535. The default value is 3600. Changing the value will not
change the configuration until the Submit button is pressed.
Reauthentication Enabled - This field allows the user to enable or disable
reauthentication of the supplicant for the specified port. The selectable values are 'true'
and 'false'. If the value is 'true' reauthentication will occur. Otherwise, reauthentication will
not be allowed. The default value is false. Changing the selection will not change the
configuration until the Submit button is pressed.
Command Buttons
Initialize - This button begins the initialization sequence on the selected port. This button
is only selectable if the control mode is 'auto'. If the button is not selectable, it will be
grayed out. Once this button is pressed, the action is immediate. It is not required to press
the Submit button for the action to occur.
Reauthenticate - This button begins the reauthentication sequence on the selected port.
To Next Page
Loading...
Need help?
General
