EasyManua.ls Logo

NXP Semiconductors MPC5566 - Pad Configuration Register 84 (SIU_PCR84)

NXP Semiconductors MPC5566
1268 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
System Integration Unit (SIU)
MPC5566 Microcontroller Reference Manual, Rev. 2
6-46 Freescale Semiconductor
Refer to Table 6-19 for bit field definitions. Table 6-49 lists the PA fields for CNTXA_TXDA_GPIO[83].
6.3.1.50 Pad Configuration Register 84 (SIU_PCR84)
The SIU_PCR84 register controls the pin function, direction, and electrical attributes of
CNRXA_RXDA_GPIO[84].
Figure 6-51. CNRXA_RXDA_GPIO[84] Pad Configuration Register (SIU_PCR84)
Refer to Table 6-19 for bit field definitions. Table 6-50 lists the PA fields for CNRXA_RXDA_GPIO[84].
6.3.1.51 Pad Configuration Register 85 (SIU_PCR85)
The SIU_PCR85 register controls the function, direction, and electrical attributes of
CNTXB_PCSC[3]_GPIO[85]. This register allows selection of the CNTXB, PCSC[3] and GPIO
functions.
Figure 6-52. CNTXB_PCSC[3]_GPIO[85] Pad Configuration Register (SIU_PCR85)
Table 6-49. PCR83 PA Field Definition
PA Field Pin Function
0b00 GPIO[83]
0b01 CNTXA
0b10 TXDA
0b11 CNTXA
Address: Base + 0x00E8 Access: R/W
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
R 0 0 0 0
PA OBE
1
1
When configured as CNRXA or RXDA, the OBE bit has no effect. When configured as GPDO, set the OBE bit to 1.
IBE
2
2
When the pad is configured as an output, set the IBE bit to 1 to show the pin state in the GPDI register.
Clear the IBE bit to 0 to reduce power consumption. When configured as GPDI, set the IBE bit to 1.
0 0
ODE HYS SRC WPE WPS
W
RESET: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
Table 6-50. PCR84 PA Field Definition
PA Field Pin Function
0b00 GPIO[84]
0b01 CNRXA
0b10 RXDA
0b11 CNRXA
Address: Base + 0x00EA Access: R/W
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
R 0 0 0 0
PA OBE
1
1
When configured as CNTXB or PCSC[3], the OBE bit has no effect. When configured as GPDO, set the OBE bit to 1.
IBE
2
2
When the pad is configured as an output, set the IBE bit to 1 to show the pin state in the GPDI register. Clear the IBE bit to 0
to reduce power consumption. When configured as GPDI, set the IBE bit to 1.
0 0
ODE HYS SRC WPE WPS
W
RESET: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1

Table of Contents

Related product manuals