Lenze E84AVHC Series - Page 1106

8400 HighLine | Parameter setting & configuration
Index
1106 L Firmware ≤ 05.00 - DMS 4.2 EN - 02/2010
F
Fan failure (C00561) 668
Fan switching status (C00560) 668
FB display input output2 (C2996) 796
FB display input/output (C2995) 796
FB Editor 820
FB xy position (C2994) 796
FB_call table (C455) 660
FC1
Field controller limitation (error message)
484
FCH1
Switching frequency reduction (error message)
483
FCH2
Maximum speed for Fchop (error message)
483
Feed constant 388
Feedback to Lenze 1116
FI brake 193
Fieldbus interface 572
Filter time - earth-fault detect. is running (C1770) 788
Filter time - oscill. damping (C00235) 630
Firmware (C00201) 627
Firmware product type (C00200) 627
Firmware update 77
Firmware version (C00099) 605
Firmware version (C00100) 605
Fixed setpoint x (L_NSet_1 n-Fix) (C00039) 597
Flying restart function 171
Activation (C00990) 757
Current (C00994) 757
Int. time (C993) 757
Process (C00991) 757
Start frequency (C00992) 757
Following error monitoring 423
Format error 542
FreqInxx
Gain (C02843)
795
Offset (C02842) 795
FreqInxx_nOut_a (C00446) 659
FreqInxx_nOut_v (C00445) 658
Frequency limitation (C00910) 750
Function assignment 694
Function block editor 820
Function L_Counter 1-3 (C01100) 763
G
Gearbox ratio 387
General data (CAN on board) 502
General purpose functions 355
GP functions (GeneralPurpose) 355
H
Hardware limit switch 391
Heartbeat protocol 543
Heatsink temperature (C00061) 599
Holding brake
Activation time (C02593)
791
Operating mode (C02580) 789
Setting (C02582) 790
Speed thresholds (C02581) 789
Status (C02607) 792
Time system (C02589) 791
Holding brake control 437
Homing 395
HW version (C210) 628
I
I-1000 551
I-1001 551
I-1003 552
I-1005 553
I-1006 554
I-1014 554
I-1016 555
I-1017 556
I-1018 556
I-1200 557
I-1201 558
I-1400 560
I-1401 561
I-1402 562
I-1600 563
I-1601 563
I-1602 564
I-1800 565
I-1801 567
I-1802 568
I-1A00 569
I-1A01 569
I-1A02 570
ICM_DiagnosticCounter (C922) 751
ICOM error number (C296) 635
ID1
Motor data identification error (error message)
482
ID3
CINH motor data identification (error message)
482
ID4
Resistance identification error (error message)
482
Identifier (CAN) 509
Identifiers of the parameter data objects 531
Identifiers of the process data objects 524
Identity object (I-1018) 556
Imax controller 115
Imax in generator mode (C00023) 594
Imax in motor mode (C00022) 594
Imax/M controller gain (C00073) 600
Imax/M controller reset time (C00074) 601
Info (C205) 628
Insert options for copied elements 863
efesotomasyon.com - Lenze