1418 Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide
Index
track measurements, 498
trademarks, 2
transfer instrument state, 175, 991
transforms, math, 390
transient response, 546
transient response analysis, 651, 652, 655
TRANsition SEARch commands, 915
transition search qualifier, 916
transition search slope, 917
transition search time, 919
transition trigger qualifier, 1068
transition trigger slope, 1069
transition trigger source, 918, 1070
transition trigger time, 1071
transmit word size, I2S, 784
tree traversal rules, 1281
trend measurement, 401
TRG (Trigger), 185, 187, 188
TRIG OUT BNC, 259
trigger armed event register, 215, 217
trigger burst, UART, 882
trigger channel source, 1045, 1076
TRIGger commands, 1007
TRIGger commands, general, 1009
trigger data, UART, 883
TRIGger DELay commands, 1019
trigger duration, 1052, 1053
TRIGger EBURst commands, 1026
TRIGger EDGE commands, 1031
trigger edge coupling, 1032
trigger edge slope, 1035
trigger edge slope, Edge Then Edge
trigger, 1024
trigger edge source, Edge Then Edge
trigger, 1025
trigger event bit, 229
Trigger Event Register (TER), 1249
TRIGger FLEXray commands, 748
TRIGger GLITch commands, 1037
trigger holdoff, 1012
trigger idle, UART, 884
TRIGger IIC commands, 786
trigger level auto set up,
1013
trigger level constants, 275
trigger level voltage, 1033
trigger level, high, 1014
trigger level, low, 1015
TRIGger LIN commands, 796
TRIGger M1553 commands, 810
trigger occurred, 187
TRIGger OR commands, 1046
TRIGger PATTern commands, 1048
trigger pattern qualifier, 1054
trigger qualifier, UART, 885
trigger reset conditions, 181, 988
TRIGger RUNT commands, 1056
TRIGger SHOLd commands, 1061
trigger SPI clock slope, 853
TRIGger SPI commands, 850
trigger status bit, 229
trigger sweep mode, 1007
TRIGger TV commands, 1067, 1072
trigger type, ARINC 429, 718, 922
trigger type, SPI, 864
trigger type, UART, 886
TRIGger UART commands, 866
TRIGger ZONE commands, 1082
trigger, ARINC 429 source, 711
trigger, CAN, 735
trigger, CAN FD sample point, 729
trigger, CAN pattern data length, 741
trigger, CAN pattern ID mode, 744
trigger, CAN sample point, 730
trigger, CAN signal baudrate, 731
trigger, CAN signal definition, 732
trigger, CAN source, 734
trigger, duration greater than, 1052
trigger, duration less than, 1053
trigger, duration range, 1055
trigger, edge coupling, 1032
trigger, edge level, 1033
trigger, edge reject, 1034
trigger, edge slope, 1035
trigger, edge source, 1036
trigger, FLEXray, 758
trigger, FLEXray error, 759
trigger, FLEXray event, 762
trigger, force a, 1010
trigger, glitch greater than, 1039
trigger, glitch less than,
1040
trigger, glitch level, 1041
trigger, glitch polarity, 1042
trigger, glitch qualifier, 1043
trigger, glitch range, 1044
trigger, glitch source, 1045
trigger, high frequency reject filter, 1011
trigger, holdoff, 1012
trigger, I2S, 776
trigger, I2S alignment, 769
trigger, I2S audio channel, 778
trigger, I2S clock slope, 771
trigger, I2S CLOCksource, 773
trigger, I2S DATA source, 774
trigger, I2S pattern data, 779
trigger, I2S pattern format, 781
trigger, I2S range, 782
trigger, I2S receiver width, 772
trigger, I2S transmit word size, 784
trigger, I2S word select (WS) low, 785
trigger, I2S word select (WS) source, 775
trigger, IIC clock source, 788
trigger, IIC data source, 789
trigger, IIC pattern address, 790
trigger, IIC pattern data, 791
trigger, IIC pattern data 2, 792
trigger, IIC qualifier, 793
trigger, IIC signal baudrate, 800
trigger, IIC type, 794
trigger, LIN, 804
trigger, LIN pattern data, 806
trigger, LIN pattern data length, 808
trigger, LIN pattern format, 809
trigger, LIN sample point, 799
trigger, LIN signal definition, 1226
trigger, LIN source, 801
trigger, mode, 1016
trigger, noise reject filter, 1017
trigger, Nth edge burst source, 1030
trigger, Nth edge in burst slope, 1029
trigger, Nth edge of burst count, 1027
trigger, Nth edge of Edge Then Edge
trigger, 1023
trigger, SPI clock slope, 853
trigger, SPI clock source, 856
trigger, SPI clock timeout, 854
trigger, SPI frame source, 857
trigger, SPI framing, 855
trigger, SPI pattern MISO width, 861
trigger, SPI pattern MOSI width, 863
trigger, sweep,
1018
trigger, threshold, 1230
trigger, TV line, 1073
trigger, TV mode, 1074, 1231
trigger, TV polarity, 1075
trigger, TV source, 1076
trigger, TV standard, 1077
trigger, UART base, 881
trigger, UART baudrate, 870
trigger, UART bit order, 871
trigger, UART parity, 877
trigger, UART polarity, 878
trigger, UART Rx source, 879
trigger, UART Tx source, 880
trigger, UART width, 887
truncation rules, 1278
TST (Self Test), 189
tstart, 1208
tstop, 1209
TTL threshold voltage for digital
channels, 313, 1184
TTL trigger threshold voltage, 1230
turn function on or off, 1196
turn off channel, 202
turn off channel labels, 327
turn off digital pod, 202
turn off math function, 202
turn off time, 537, 617
turn on channel labels, 327
turn on channel number display, 1189
turn on time, 538, 617
turn on/turn off time analysis, 614, 615,
616, 617
turning channel display on and off, 270
turning off/on function calculation, 377
turning vectors on or off, 1188
TV mode, 1074, 1231
TV trigger commands, 1067, 1072
TV trigger line number setting, 1073
TV trigger mode, 1076
TV trigger polarity, 1075
TV trigger standard setting, 1077
TV triggering, 1008
tvmode,
1231
Tx data, UART, 1115
Tx frame count (UART), 875
Tx source, 880
To Next Page
Loading...
