Keysight Technologies InfiniiVision 3000T X Series - Page 1419

Index
Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide 1419
type of power being converted, efficiency
measurement, 596
U
UART base, 881
UART baud rate, 870
UART bit order, 871
UART frame counters, reset, 873
UART parity, 877
UART polarity, 878
UART Rx source, 879
UART SEARch commands, 974
UART serial search, data, 975
UART serial search, data qualifier, 977
UART serial search, mode, 976
UART trigger burst, 882
UART trigger commands, 866
UART trigger data, 883
UART trigger idle, 884
UART trigger qualifier, 885
UART trigger type, 886
UART Tx data, 1115
UART Tx source, 880
UART width, 887
UART/RS232 demo signal, 301
UART/RS-232 triggering, 698
units (vertical) for FFT, 361, 382
units per division, 283, 284, 343, 1001
units per division (vertical) for FFT
function, 356
units per division (vertical) for
function, 283, 396
units, automask, 557
units, X cursor, 435, 436
units, Y cursor, 440, 441
unsigned data, 1094
unsigned mode, 1117
upper threshold, 488
upper threshold voltage for
measurement, 1211
uppercase characters in commands, 1277
URQ (User Request) status bit, 171, 173
USB (Device) interface, 43
USB triggering, 1008
user defined channel labels, 273
user defined threshold, 1184
user event conditions occurred, 187
User Files directory, 663
, 682
user name, network domain, 416
User's Guide, 6
user-defined threshold voltage for digital
channels, 313
user-defined trigger threshold, 1230
USR (User Event bit), 185, 187
utilization, CAN bus, 727
V
valid command strings, 1277
valid pattern time, 1052, 1053
value, 509
value measured at base of waveform, 475,
513
value measured at specified time, 519
value measured at top of waveform, 520
value ranges, 162
values required to fill time buckets, 234
VBA, 54, 1286
Vce(sat) power measurement, 547
Vce(sat) value for conduction
calculation, 649
vectors turned on or off, 1188
vectors, display, 332
vectors, turning on or off, 316
vernier, channel, 285
vernier, horizontal, 1002
vertical adjustment, fine (vernier), 285
vertical amplitude measurement, 473, 511
vertical axis defined by RANGe, 354, 394
vertical axis range for channels, 282
vertical offset for channels, 274
vertical peak-to-peak measured on
waveform, 476, 516
vertical scale, 283, 356, 396
vertical scaling, 1106
vertical threshold, 1184
vertical units for FFT, 361, 382
vertical value at center screen, 353, 355,
389, 395
vertical value maximum measured on
waveform, 514
vertical value measurements to calculate
overshoot, 485
vertical value minimum measured on
waveform, 515
video line to trigger on, 1073
video standard selection, 1077
view, 230, 1118, 1189
view turns function on or off,
1196
VISA COM example in C#, 1295
VISA COM example in Python, 1312
VISA COM example in Visual Basic, 1286
VISA COM example in Visual Basic
.NET, 1304
VISA example in C, 1319
VISA example in C#, 1338
VISA example in Python, 1359
VISA example in Visual Basic, 1328
VISA example in Visual Basic .NET, 1349
VISA examples, 1286, 1319
Visual Basic .NET, SCPI.NET example, 1392
Visual Basic .NET, VISA COM
example, 1304
Visual Basic .NET, VISA example, 1349
Visual Basic 6.0, 55
Visual Basic for Applications, 54, 1286
Visual Basic, SICL library example, 1375
Visual Basic, VISA COM example, 1286
Visual Basic, VISA example, 1328
visualizations, math, 391
voltage crossing reported or not
found, 1210
voltage difference between data
points, 1122
voltage difference measured, 1212
voltage level for active trigger, 1033
voltage marker used to measure
waveform, 1213, 1214
voltage offset value for channels, 274
voltage probe, 284, 343
voltage ranges for channels, 282
voltage ranges for external trigger, 342
voltage source, 642
voltage threshold, 468
voltage, maximum expected input, 635,
636, 637
W
WAI (Wait To Continue), 190
wait, 190
wait for operation complete, 176
Wait Trig bit, 215, 217
waveform base value measured, 475, 513
WAVeform command, 53
WAVeform commands, 1089
waveform data, 1091
waveform data format, 691
waveform data length, 692
waveform data length, maximum, 693
waveform data, save, 690
waveform generator, 1128
waveform generator amplitude, 1161
waveform generator function, 1137
waveform generator high-level
voltage, 1162
waveform generator low-level
voltage, 1163
waveform generator offset, 1164
waveform generator output control, 1156
waveform generator output load
impedance, 1157
waveform generator output polarity, 1158
waveform generator period, 1159
waveform generator pulse width, 1141
waveform generator ramp symmetry, 1142
waveform generator reset defaults, 1160
waveform generator square wave duty
cycle, 1143
waveform introduction, 1091
waveform maximum vertical value
measured, 514
waveform minimum vertical value
measured, 515
waveform must cross voltage level to be an
occurrence, 1210
WAVeform parameters, 58
waveform peak-to-peak vertical value
measured, 476, 516
waveform period, 488
waveform persistence, 316