Index
Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide 1417
SPI MISO data, 1115
SPI SEARch commands, 970
SPI serial search, data, 972
SPI serial search, data width, 973
SPI serial search, mode, 971
SPI trigger, 855, 861, 863
SPI trigger clock, 856
SPI trigger commands, 850
SPI trigger frame, 857
SPI trigger MISO data pattern, 860
SPI trigger MOSI data pattern, 862
SPI trigger type, 864
SPI trigger, MISO data source, 858
SPI trigger, MOSI data source, 859, 1227
SPI triggering, 698
square math function, 390
square root math function, 390
square wave duty cycle, waveform
generator, 1143
square waveform generator output, 1137
SRE (Service Request Enable
Register), 185, 1248
SRQ (Service Request interrupt), 205, 209,
213
SSM pattern, ARINC 429 trigger, 716, 925
standard deviation measured on
waveform, 497
Standard Event Status Enable Register
(ESE), 170, 1253
Standard Event Status Register (ESR), 172,
1252
standard for video, 1077
standard, LIN, 802
start acquisition, 188, 203, 224, 226
start and stop edges, 468
start cursor, 1208
start frequency, FFT math function, 359,
379
start measurement, 458
start print job, 419
start time, 1044, 1208
start time marker,
1205
starting bit for SENT Fast Channel
Signal, 836
state memory, 183
state of instrument, 175, 991
statistics increment, 503
statistics reset, 505
statistics results, 493
statistics, max count, 504
statistics, relative standard deviation, 506
statistics, type of, 501
status, 186, 227, 229
Status Byte Register (STB), 184, 186, 187,
1246
status data structure clear, 169
status registers, 62
status reporting, 1241
STB (Status Byte Register), 184, 186, 187,
1246
steady state output voltage expected, 638,
639, 640
step size for frequency span, 358, 381
stop, 203, 228
stop acquisition, 228
stop cursor, 1209
stop displaying channel, 202
stop displaying math function, 202
stop displaying pod, 202
stop frequency, FFT math function, 360,
380
stop on mask test failure, 572
stop time, 1044, 1209
storage, 183
store instrument setup, 175, 183
store setup, 183
storing calibration information, 258
string variables, 60
string variables, reading multiple query
results into, 61
string variables, reading query results into
multiple,
61
string, quoted ASCII, 162
subnet mask, 44
subsource, waveform source, 1115
subsystem commands, 3, 1281
subtract math function, 390, 1111
subtract math function as g(t) source, 1192
sweep mode, trigger, 1007, 1018
sweep speed set to fast to measure fall
time, 479
sweep speed set to fast to measure rise
time, 496
switch disable, 984
switching level, current, 647
switching level, voltage, 650
switching loss per cycle, 531
switching loss power analysis, 645
sync break, LIN, 803
sync frame count (FlexRay), 755
syntax elements, 161
syntax rules, program data, 1280
syntax, optional terms, 161
syntax, program message, 1277
SYSTem commands, 979
system commands, 981, 982, 983, 984,
991, 993
system commands introduction, 980
T
table of current harmonics results, 600
tdelta, 1204
tedge, 507
Tektronix probe model number, 278
telnet ports 5024 and 5025, 1099
Telnet sockets, 63
temporary message, 982
TER (Trigger Event Register), 229, 1249
termination conditions, mask test, 568
test sigma, mask test run, 573
test, self, 189
text, writing to display, 982
THD (total harmonics distortion), 607
threshold, 313, 587, 1184, 1230
threshold for FFT peak search, 909
threshold voltage (lower) for
measurement, 1202
threshold voltage (upper) for
measurement, 1211
thresholds, 468, 1205
thresholds used to measure period, 488
thresholds, how autoscale affects, 197
time base, 997, 998, 999, 1000, 1001,
1229
time base commands introduction, 996
time base reset conditions, 181, 988
time base window, 1003, 1004, 1005
time between points, 1204
time buckets, 233, 234
time delay, 1229
time delay, Edge Then Edge trigger, 1022
time delta, 1204
time difference between data points, 1119
time duration, 1044, 1052, 1053, 1055
time holdoff for trigger, 1012
time interval,
507, 509, 1204
time interval between trigger and
occurrence, 1210
time marker sets start time, 1205
time measurements with X cursors, 435
time per division, 999
time record, 362, 383
time reference, lister, 424
time specified, 519
time, calibration, 264
time, mask test run, 574
time, runt pulse search, 914
time, runt trigger, 1060
time, start marker, 1208
time, stop marker, 1209
time, system, 993
time, transition search, 919
time, transition trigger, 1071
time/div, how autoscale affects, 197
time-at-max measurement, 1206
time-at-min measurement, 1207
TIMebase commands, 995
timebase vernier, 1002
TIMebase:MODE, 58
time-ordered label list, 328
timeout, SPI clock, 854
timing measurement, 458
title channels, 273
title, mask test, 582
tolerance for determining valid SENT sync
pulses, 840
tolerance, automask, 558, 559
top of waveform value measured, 520
total frame count (CAN), 726
total frame count (FlexRay), 756
total harmonics distortion (THD), 607
total waveforms in mask test, 563
touchscreen on/off, 994
trace memory, 227
To Next Page
Loading...
