Keysight Technologies InfiniiVision 3000T X Series User Manual

1416 Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide
Index
SEARch commands, GLITch, 898
SEARch commands, I2S, 942
SEARch commands, IIC, 948
SEARch commands, LIN, 955
SEARch commands, M1553, 961
SEARch commands, PEAK, 905
SEARch commands, RUNT, 910
SEARch commands, SENT, 965
SEARch commands, SPI, 970
SEARch commands, TRANsition, 915
SEARch commands, UART, 974
search event (found) times, saving, 687
search for found event, 892
search mode, 893
search state, 894
search, edge slope, 896
search, edge source, 897
SECAM, 1073, 1077
seconds per division, 1001
segmented memory acquisition times, 688
segmented waveform save option, 694
segments, analyze, 237
segments, count of waveform, 1109
segments, setting number of memory, 238
segments, setting the index, 239
segments, time tag, 1110
select measurement channel, 499
self-test, 189
sensing a channel probe, 1187
sensing a external trigger probe, 1191
sensitivity of oscilloscope input, 275
SENT demo signal, 303
SENT enhanced serial message ID and data
lengths, 848
SENT fast channel data search value, 966
SENT fast channel data trigger setting, 843
SENT FAST data, 1115
SENT input source, 838
SENT percent tolerance variation
trigger, 849
SENT SEARch commands, 965
SENT search mode, 967
SENT serial bus commands, 817
SENT signal length setting, 830
SENT signals display setting, 829
SENT slow channel data search value, 968
SENT slow channel ID and data trigger data
setting, 844
SENT slow channel ID search value, 969
SENT slow channel ID trigger setting, 846
SENT SLOW data, 1115
SENT trigger mode, 841
SENT triggering, 698
sequential commands, 1284
serial clock, 788, 856
serial data, 789
serial decode bus, 697
serial decode bus display, 700
serial decode mode, 701
serial frame, 857
serial number, 225
service request, 187
Service Request Enable Register
(SRE), 185, 1248
set center frequency, 348, 378
set cursors, 1208, 1209
set date, 981
set time, 993
set up oscilloscope, 43
setting digital display, 309
setting digital label, 252, 310
setting digital position, 311
setting digital threshold, 313
setting display, 377
setting external trigger level, 339
setting impedance for channels, 271
setting inversion for channels, 272
setting pod display, 585
setting pod size, 586
setting pod threshold, 587
settings, 179, 183
settings, instrument, 404
setup, 232, 246, 267, 308, 316, 404,
991
setup and hold trigger clock source, 1063
setup and hold trigger data source, 1064
setup and hold trigger hold time, 1065
setup and hold trigger setup time, 1066
setup and hold trigger slope, 1062
setup configuration, 179, 183, 991
setup defaults, 180, 987
setup memory, 179
setup reported, 1008
setup time, setup and hold trigger, 1066
setup, recall, 664
setup, save, 689
shape of modulation signal, waveform
generator, 1150
SHOLd trigger commands, 1061
short form, 5, 1278
show channel labels, 327
show measurements, 458, 498
SICL example in C, 1366
SICL example in Visual Basic, 1375
SICL examples, 1366
sidebar, display, 330
sigma, mask test run, 573
signal speed, ARINC 429, 712
signal type, 280
signal type, ARINC 429, 710
signal value, CAN symbolic search, 935
signal value, CAN symbolic trigger, 747
signal, CAN symbolic search, 934
signal, CAN symbolic trigger, 746
signed data, 1094
simple command headers, 1279
sine cardinal waveform generator
output, 1139
sine waveform demo signal, 300
sine waveform generator output, 1137
single acquisition, 226
single-ended probe heads, 276
single-ended signal type, 280
single-shot demo signal, 300
single-shot DUT, synchronizing with, 1270
size, 586
size, digital channels, 312
skew, 279, 1185
skew reference waveform, 1171
slew rate power analysis, 643
slope, 853, 1035
slope (direction) of waveform, 1210
slope not valid in TV trigger mode, 1035
slope parameter for delay
measurement, 470
slope, arming edge, Edge Then Edge
trigger, 1020
slope, Nth edge in burst, 1029
slope, setup and hold trigger, 1062
slope, transition search, 917
slope, transition trigger, 1069
slope, trigger edge, Edge Then Edge
trigger, 1024
slot, network printer, 415
SLOW data, SENT, 1115
smoothing acquisition type, 1093
smoothing math function, 391
smoothing math function, number of
points, 397
snapshot all measurement, 460
software version, 174
source, 499, 711, 734, 801
source (voltage or current) for slew rate
analysis, 644
source channel, M1553, 813
source for function, 1195
source for glitch search, 904
source for Nth edge burst trigger, 1030
source for trigger, 1036
source for TV trigger, 1076
source function for FFT peak search, 908
source input for FFT function, 357
source input for function, first, 398
source input for function, second, 400
source, arming edge, Edge Then Edge
trigger, 1021
source, automask, 556
source, FLEXray, 757
source, mask test, 581
source, runt search, 913
source, runt trigger, 1059
source, save reference waveform, 695
source, transition trigger, 918, 1070
source, trigger edge, Edge Then Edge
trigger, 1025
source, waveform, 1111
span, 390
span of frequency on display, 358, 381
Spec error counter (CAN), 725
specify measurement, 499
speed of ARINC 429 signal, 712
SPI, 853
SPI clock timeout, 854
SPI decode bit order, 852
SPI decode word width, 865
SPI demo signal, 302

Keysight Technologies InfiniiVision 3000T X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 3000T X Series
Category	Test Equipment
Language	English