Keysight Technologies InfiniiVision 3000T X Series User Manual

Index
Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide 1415
range for duration trigger, 1055
range for external trigger, 342
range for full-scale vertical axis, 354, 394
range for glitch search, 903
range for glitch trigger, 1044
range for time base, 999
range of offset values, 274
range qualifier, 1043
range, I2S, 782
ranges, value, 162
rate, 242
ratio measurements with X cursors, 435
ratio measurements with Y cursors, 440
ratio of AC RMS values measured between
channels, 517
Ratio, power modulation analysis, 613
raw acquisition record, 1104
RCL (Recall), 179
Rds (dynamic ON resistance)
waveform, 646
Rds(on) power measurement, 542
Rds(on) value for conduction
calculation, 648
reactive power, 543
read configuration, 175
ReadIEEEBlock method, 55, 59, 61
ReadList method, 55, 59
ReadNumber method, 55, 59
readout, 1204
ReadString method, 55, 59
real power, 544
real-time acquisition mode, 235
recall, 179, 658, 991
recall arbitrary waveform, 659
recall CAN symbolic data, 660
RECall commands, 657
recall filename, 661, 1136
recall mask, 662
recall path information, 663
recall reference waveform, 665
recall setup, 664
recalling and saving data, 316
receiver width, I2S, 772
RECTangular window for transient
signals, 362, 383
reference, 369, 1000
reference for time base, 1229
reference waveform save source, 695
reference waveform, recall, 665
reference waveform, save, 696
reference waveforms, clear, 1167
reference waveforms, display, 1168
reference waveforms, label, 1169
reference waveforms, save to, 1170
reference waveforms, skew, 1171
reference waveforms, Y offset, 1172
reference waveforms, Y range, 1173
reference waveforms, Y scale, 1174
reference, lister, 424
registers, 172, 179, 183, 196, 209, 211,
213, 215, 217, 219, 221
registers, clearing, 1262
reject filter, 1034
reject high frequency, 1011
reject noise, 1017
relative standard deviation, 506
remote control examples, 1285
Remote Terminal Address (RTA), M1553
trigger, 815
remove cursor information, 429
remove labels, 327
remove message from display, 982
reorder channels, 197
repetitive acquisitions, 224
report errors, 983
report transition, 507, 509
reporting status, 1241
reporting the setup, 1008
request service, 187
Request-for-OPC flag clear, 169
reset, 180
reset conditions, 180
reset defauts, waveform generator, 1160
reset mask statistics, 561
reset measurements, 324
resolution of printed copy, 1199
resource session object, 55
ResourceManager object, 55
restore configurations, 175, 179, 183, 991
restore labels, 327
restore setup, 179
return values, query, 1283
returning acquisition type, 243
returning number of data points, 236
RF burst demo signal, 301
right reference, 1000
ringing pulse demo signal, 300
ripple (output) analysis, 623
ripple, output, 545
rise time measurement, 458
rise time of positive edge, 496
Rise Time, power modulation analysis, 613
rising edge count measurement, 487
rising pulse count measurement, 490
RMS - AC, power modulation analysis, 613
RMS value measurement, 477, 518
roll time base mode, 997
root (:) commands, 191, 194
root level commands, 3
RQL (Request Control) status bit, 171, 173
RQS (Request Service), 187
RS-232/UART triggering, 698
RST (Reset), 180
rules, tree traversal, 1281
rules, truncation, 1278
run, 188, 224
Run bit, 215, 217
run count, current harmonics analysis, 604
run mode, mask test, 568
running configuration, 183, 991
RUNT SEARch commands, 910
runt search polarity, 911
runt search qualifier, 912
runt search source,
913
runt search, pulse time, 914
RUNT trigger commands, 1056
runt trigger polarity, 1057
runt trigger qualifier, 1058
runt trigger source, 1059
runt trigger time, 1060
Rx frame count (UART), 874
Rx source, 879
S
sample rate, 3, 242
sampled data, 1188
sampled data points, 1099
SAV (Save), 183
save, 183, 669
save arbitrary waveform, 671
SAVE commands, 667
save current harmonics analysis
results, 681
save filename, 672
save image, 673
save image with inksaver, 676
save mask, 678, 679
save mask test failures, 571
save path information, 682
save reference waveform, 696
save setup, 689
save to reference waveform location, 1170
save waveform data, 690
saved image, area, 1225
saving and recalling data, 316
SBUS A429 commands, 702
SBUS CAN commands, 719
SBUS commands, 697
SBUS I2S commands, 767
SBUS SENT commands, 817
SBUS<n> commands, general, 699
scale, 356, 396, 1001, 1005
scale factors output on hardcopy, 407, 674
scale for channels, 283
scale units for channels, 284
scale units for external trigger, 343
scaling display factors, 275
SCPI commands, 63
SCPI.NET example in C#, 1386
SCPI.NET example in IronPython, 1398
SCPI.NET example in Visual Basic
.NET, 1392
SCPI.NET examples, 1386
scratch measurements, 1203
screen area for hardcopy print, 405
screen area for saved image, 1225
screen image data, 325
SDI pattern, ARINC 429 trigger, 715,
924
SEARch commands, 889
SEARch commands, A429, 920
SEARch commands, CAN, 926
SEARch commands, EDGE, 895
SEARch commands, FLEXray, 936
SEARch commands, general, 890

Keysight Technologies InfiniiVision 3000T X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 3000T X Series
Category	Test Equipment
Language	English