Keysight Technologies InfiniiVision 3000T X Series User Manual

1406 Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide
Index
averaged value math function, 391
averaging acquisition type, 232, 1093
averaging, synchronizing with, 1272
Ax + B math function, 390
B
bandwidth filter limits, 340
bandwidth filter limits to 20 MHz, 268
bar chart of current harmonics results, 600
base 10 exponential math function, 390
base value measurement, 475, 513
base, ARINC 429, 705
base, I2S serial decode, 770
base, MIL-STD-1553 serial decode, 812
base, SENT decode, 822
base, UART trigger, 881
basic instrument functions, 168
baud rate, 731, 800, 870
baud rate, CAN FD, 733
begin acquisition, 203, 224, 226
BHARris window for minimal spectral
leakage, 362, 383
binary block data, 162, 325, 991, 1099
BINary waveform data format, 691
bind levels for masks, 576
bit order, 871
bit order, SPI decode, 852
bit rate measurement, 462
bit selection command, bus, 247
bit weights, 172
bitmap display, 325
bits in Service Request Enable
Register, 185
bits in Standard Event Status Enable
Register, 171
bits in Status Byte Register, 187
bits selection command, bus, 248
blank, 202
block data, 162, 175, 991
block response data, 60
blocking synchronization, 1267
blocking wait, 1266
BMP format screen image data, 325
braces, 161
built-in measurements, 53
burst data demo signal, 301
burst width measurement,
463
burst, minimum time before next, 1028
bus bit selection command, 247
bus bits selection commands, 248
bus clear command, 250
bus commands, 246
BUS data format, 1096
bus display, 251
bus label command, 252
bus mask command, 253
BUS<n> commands, 245
button disable, 984
button, calibration protect, 260
byte format for data transfer, 1095, 1101
BYTeorder, 1097
C
C, SICL library example, 1366
C, VISA library example, 1319
C#, SCPI.NET example, 1386
C#, VISA COM example, 1295
C#, VISA example, 1338
CAL PROTECT button, 260
CAL PROTECT switch, 256
calculating preshoot of waveform, 491
calculating the waveform overshoot, 485
calibrate, 257, 258, 260, 264
CALibrate commands, 255
calibrate date, 257
calibrate introduction, 256
calibrate label, 258
calibrate output, 259
calibrate start, 261
calibrate status, 262
calibrate switch, 260
calibrate temperature, 263
calibrate time, 264
CAN acknowledge, 730
CAN and LIN demo signal, 302
CAN baud rate, 731
CAN demo signal, 301
CAN FD baud rate, 733
CAN FD data triggers, starting byte
position, 742
CAN frame counters, reset, 724
CAN SEARch commands, 926
CAN serial bus commands, 719
CAN serial search, data, 929
CAN serial search, data length, 930
CAN serial search, ID, 931
CAN serial search, ID mode, 932
CAN serial search, mode, 927
CAN signal definition, 732
CAN source, 734
CAN symbolic data display, 728
CAN symbolic data, recall, 660
CAN trigger, 735, 741
CAN trigger data pattern, 739
CAN trigger ID pattern, 743
CAN trigger pattern id mode, 744
CAN trigger, ID filter for, 738
CAN triggering, 697
capture data, 203
capturing data, 52
cardiac waveform generator output, 1139
center frequency set, 348, 378, 390
center of screen, 1124
center reference, 1000
center screen, FFT vertical value at, 353,
355
center screen, vertical value at, 389, 395
CFD demo signal, 303
channel, 230, 273, 1182, 1184
channel coupling, 269
channel display, 270
channel input impedance, 271
channel inversion, 272
channel label, 273, 1183
channel labels, 327, 328
channel numbers, 1189
channel overload, 281
channel protection, 281
channel reset conditions, 180, 987
channel selected to produce trigger, 1045,
1076
channel signal type, 280
channel skew for oscilloscope probe, 279,
1185
channel status, 227, 1189
channel threshold, 1184
channel vernier, 285
channel, stop displaying, 202
CHANnel<n> commands, 265, 267
channels to autoscale, 200
channels, how autoscale affects, 197
characters to display, 982
chart logic bus state math function, 392
chart logic bus state, clock edge, 372
chart logic bus state, clock source, 371
chart logic bus timing math function, 392
chart logic bus, units, 375
chart logic bus, value for data = 0, 374
chart logic bus, value for data
increment, 373
classes of input signals, 362, 383
classifications, command, 1276
clear, 324
clear bus command, 250
clear cumulative edge variables, 1182
clear FFT function, 349
clear markers, 464, 1203
clear measurement, 464, 1203
clear message queue, 169
Clear method, 55
clear reference waveforms, 1167
clear screen, 1190
clear status, 169
clear waveform area, 316
clipped high waveform data value, 1099
clipped low waveform data value, 1099
clock, 788, 853, 856
clock period, SENT signal, 820
clock slope, I2S, 771
CLOCk source, I2S, 773
clock source, setup and hold trigger, 1063
clock timeout, SPI, 854
clock with infrequent glitch demo
signal, 300
CLS (Clear Status), 169
CME (Command Error) status bit, 171, 173
CMOS threshold voltage for digital
channels, 313, 1184
CMOS trigger threshold voltage, 1230
code, :ACQuire:COMPlete, 233
code, :ACQuire:SEGMented, 239
code, :ACQuire:TYPE, 244

Keysight Technologies InfiniiVision 3000T X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 3000T X Series
Category	Test Equipment
Language	English