Keysight Technologies InfiniiVision 3000T X Series User Manual

1408 Keysight InfiniiVision 3000T X-Series Oscilloscopes Programmer's Guide
Index
date, system, 981
dB versus frequency, 390
DC coupling for edge trigger, 1032
DC input coupling for specified
channel, 269
DC offset correction for integrate
input, 386
DC RMS measured on waveform, 477, 518
DC waveform generator output, 1138
DCMotor demo signal, 302
DDE (Device Dependent Error) status
bit, 171, 173
decision chart, status reporting, 1263
default conditions, 180, 987
define channel labels, 273
define glitch trigger, 1043
define logic thresholds, 1184
define measurement, 468
define measurement source, 499
define trigger, 1044, 1052, 1053, 1055
defined as, 161
definite-length block query response, 60
definite-length block response data, 162
delay measured to calculate phase, 489
delay measurement, 468
delay measurements, 507
delay parameters for measurement, 470
delay time, Edge Then Edge trigger, 1022
DELay trigger commands, 1019
delay, how autoscale affects, 197
delayed time base, 997
delayed window horizontal scale, 1005
delete mask, 565
delta time, 1204
delta voltage measurement, 1212
delta X cursor, 426
delta Y cursor, 426
demo, 299
DEMO commands, 299
demo signal, 301
demo signal function, 300
demo signal phase angle, 304
demo signals output control, 305
deskew for power measurements, 594
detecting probe types, 1187, 1191
device-defined error queue clear, 169
DIFF source for function, 1195
differences from 4000 X-Series oscilloscope
commands, 35
differential probe heads, 276
differential signal type, 280
differentiate math function, 390, 1111
digital channel commands, 308, 309, 310,
311, 313
digital channel data, 1095
digital channel labels, 328
digital channel order, 1189
digital channel source for glitch
trigger, 1045
digital channels, 6
digital channels, activity and logic levels
on, 195
digital channels, groups of, 583, 585, 587
digital pod, stop displaying, 202
digital reset conditions, 181, 988
DIGital<d> commands, 307
digitize channels, 203
DIGitize command, 52, 57, 1092
digits, 162
disable front panel, 984
disable function, 1196
disabling calibration, 260
disabling channel display, 270
disabling status register bits, 170, 184
discontinued and obsolete
commands, 1175
display annotation, 318
display annotation background, 319
display annotation color, 320
display annotation text, 321
display channel labels, 327
display clear, 324
DISPlay commands, 315
display commands introduction, 316
display connect, 1188
display date, 981
display factors scaling, 275
display for channels,
270
display frequency span, 358, 381
display measurements, 458, 498
display mode, FFT, 351
display order, 1189
display persistence, 331
display reference, 998, 1000
display reference waveforms, 1168
display reset conditions, 181, 988
display serial number, 225
display vectors, 332
display wave position, 1189
display, FFT function, 350
display, lister, 423
display, measurement statistics on/off, 502
display, oscilloscope, 309, 331, 377, 585,
982
display, serial decode bus, 700
displaying a baseline, 1018
displaying unsynchronized signal, 1018
divide math function, 390
DLC value in CAN FD trigger, 740
DNS IP, 44
domain, 44
domain, network printer, 413
driver, printer, 1201
DSO models, 6
duplicate mnemonics, 1281
duration, 1052, 1053, 1055
duration for glitch trigger, 1039, 1040,
1044
duration of power analysis, 627, 628, 629,
630, 631, 632
duration qualifier, trigger, 1052, 1053
duration triggering, 1008
duty cycle measurement, 53
, 458, 478,
481
Duty Cycle, power modulation
analysis, 613
DVM commands, 333
DVM displayed value, 335
DVM enable/disable, 336
DVM input source, 338
DVM mode, 337
E
EBURst trigger commands, 1026
ECL channel threshold, 1184
ECL threshold voltage for digital
channels, 313
ECL trigger threshold voltage, 1230
edge activity, 1182
edge counter, Edge Then Edge
trigger, 1023
edge counter, Nth edge of burst, 1027
edge coupling, 1032
edge fall time, 479
edge parameter for delay
measurement, 470
edge preshoot measured, 491
edge rise time, 496
EDGE SEARch commands, 895
edge search slope, 896
edge search source, 897
edge slope, 1035
edge source, 1036
edge string for OR'ed edge trigger, 1047
EDGE trigger commands, 1031
edge triggering, 1008
edges (activity) on digital channels, 195
edges in measurement, 468
efficiency, 533
efficiency power analysis, apply, 595
elapsed time in mask test, 562
ellipsis, 162
enable channel labels, 327
enabling calibration, 260
enabling channel display, 270
enabling status register bits, 170, 184
end of string (EOS) terminator, 1278
end of text (EOT) terminator, 1278
end or identify (EOI), 1278
energy loss, 534
envelope math function, 391
EOI (end or identify), 1278
EOS (end of string) terminator, 1278
EOT (end of text) terminator, 1278
erase data, 324
erase measurements, 1203
erase screen, 1190
error counter (ARINC 429), 706
error counter (ARINC 429), reset, 707
error frame count (CAN), 722
error frame count (UART), 872
error messages, 983, 1233
error number, 983
error queue, 983, 1254

Keysight Technologies InfiniiVision 3000T X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 3000T X Series
Category	Test Equipment
Language	English