Xerox WorkCentre 7132 - Page 1470

January 2007
6-147
WorkCentre 7132
Controller & Fax NVM List
General procedures information
Reversion 4.0
820-026 Scan Illegal Operation (Operation when
there was no specific Timing when an error
occurs in storing)
0~1 1: Enable stored
documents (Default
value before PL2
was 0)
Read/Write 0: Discard stored documents, 1: Enable stored documents
820-027 Scan resolution in “G3 Auto” or “Interna-
tional Communication”
0~2 2=Fine (600/400) is
Inch series, and oth
-
ers are millimeter
series
Read/Write 0: Select the resolution for millimeter series 1: Select the resolu-
tion for inch series 2: Fine (600/400) is for inch series and others
for millimeter series
820-028 Letter/Legal Scan Instruction (Specify
whether to reduce Letter/Legal to A4 to
scan)
0~1 0: 100% Read/Write 0: 100%, 1: Reduce to A4
820-030 0= Preparing for use. Checking whether
the machine can switch to Ready mode. 1=
Can be used 255= Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 1: Can be used 255: Cannot be used
820-031 0= Preparing for use. Checking whether
the machine can switch to Ready mode.
2=G3 PSTN can be used 3=G3 ISDN can
be used 4=G4 ISDN can be used 5=G3
can be used 255=Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 2: G3 PSTN can be used 3: G3 ISDN can be
used 4: G4 ISDN can be used 5: G3 can be used 255: Cannot
be used
820-032 0= Preparing for use. Checking whether
the machine can switch to Ready mode.
2=G3 PSTN can be used 3=G3 ISDN can
be used 4=G4 ISDN can be used 5=G3
can be used 255=Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 2: G3 PSTN can be used 3: G3 ISDN can be
used 4: G4 ISDN can be used 5: G3 can be used 255: Cannot
be used
820-033 0= Preparing for use. Checking whether
the machine can switch to Ready mode.
2=G3 PSTN can be used 3=G3 ISDN can
be used 4=G4 ISDN can be used 5=G3
can be used 255=Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 2: G3 PSTN can be used 3: G3 ISDN can be
used 4: G4 ISDN can be used 5: G3 can be used 255: Cannot
be used
820-034 0= Preparing for use. Checking whether
the machine can switch to Ready mode.
2=G3 PSTN can be used 3=G3 ISDN can
be used 4=G4 ISDN can be used 5=G3
can be used 255=Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 2: G3 PSTN can be used 3: G3 ISDN can be
used 4: G4 ISDN can be used 5: G3 can be used 255: Cannot
be used
820-035 0= Preparing for use. Checking whether
the machine can switch to Ready mode.
2=G3 PSTN can be used 3=G3 ISDN can
be used 4=G4 ISDN can be used 5=G3
can be used 255=Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 2: G3 PSTN can be used 3: G3 ISDN can be
used 4: G4 ISDN can be used 5: G3 can be used 255: Cannot
be used
820-036 0= Preparing for use. Checking whether
the machine can switch to Ready mode.
2=G3 PSTN can be used 3=G3 ISDN can
be used 4=G4 ISDN can be used 5=G3
can be used 255=Cannot be used
0~255 - Read 0: Preparing for use. Checking whether the machine can switch
to Ready mode. 2: G3 PSTN can be used 3: G3 ISDN can be
used 4: G4 ISDN can be used 5: G3 can be used 255: Cannot
be used
820-037 Maximum No. of Storage ~999 999 sheets Read/Write 1~999 sheets
Table 11 NVM 825 FAX Service
Chain-Link NVM Name
Setup
Range Initial Value Read/Write Description