Xerox WorkCentre 7132 Service Documentation

January 2007
2-651
WorkCentre 7132
072-940
Status-indicator-raps
Revision
072-940 Tray 2/TTM 2 Lift Up RAP
BSD-ON:7.9/7.11
The Tray 2/TTM 2 Level Sensor did not actuate in time after the Tray 2 Feed/Lift Motor ener-
gized.
Initial Actions
Ensure the tray is set up and loaded correctly.
Procedure
Remove the tray and reinstall. The Tray 2 Feed/Lift Motor can be heard (the lifted paper
plate drops when the tray is opened).
YN
Execute Component Control [071-001/002 Tray 2 Feed/Lift Motor ON]. The Tray 2 Feed/
Lift Motor (PL 14.3/PL 15.6) can be heard (the lifted paper plate drops when the tray
is opened).
YN
Check the connections of P/J220B, P/J661B and P/J549. P/J220B, P/J661B
and P/J549 are connected correctly.
YN
Connect P/J220B, P/J661B and P/J549.
Remove the Tray 1 Feed/Lift Motor (PL 2.3 and the Tray 2 Feed/Lift Motor (PL 14.3/
PL 15.6).
Replace the Tray 2 Feed/Lift Motor with the Tray 1 Feed/Lift Motor.
Execute Component Control [071-001/002 Tray 2 Feed/Lift Motor ON]. The Tray 2
Feed/Lift Motor can be heard (the lifted paper plate drops when the tray is
opened).
YN
Return the Tray 1 Feed/Lift Motor to its original position.
Check the wires between P/J220B and P/J549 for an open circuit or a short
circuit (BSD 7.9 Flag 1/7.11 Flag 1).
The circuit between P/J220B and P/
J549 is conducting without an open circuit or a short circuit.
YN
Repair the open circuit or short circuit.
Replace the Tray Module PWB (PL 14.7/PL 15.9).
Return the Tray 1 Feed/Lift Motor to its original position.
Replace the Tray 2 Feed/Lift Motor (PL 14.3/PL 15.6).
Go to the OF 2 (SIZE SWITCH ASSY RAP).
Check the installation of the Tray 2 Level Sensor (PL 14.3/PL 15.6) and the operation of the
actuator.
The Tray 2 Level Sensor is installed correctly and the actuator works.
YN
Reinstall the Tray 2 Level Sensor (PL 14.3/PL 15.6).
Execute Component Control [072-102 Tray 2 Level Sensor]. Manually activate the Tray 2 Level
Sensor (PL 14.3/PL 15.6).
The display changes.
YN
Check the connections of P/J101B, P/J661B and P/J549. Connectors are connected
correctly.
YN
Connect P/J101B, P/J661B and P/J549.
Check the wires between P/J101B and P/J549 for an open circuit or a short circuit (BSD
7.9 Flag 2 Flag 3/7.11 Flag 2 Flag 3).
The wires between P/J101B and P/J549 are
conducting without an open circuit or a short circuit.
YN
Repair the open circuit or short circuit.
Measure the voltage between the Tray Module PWB P/J549-22 (+) and P/J549-23 (-)
(BSD 7.9 Flag 3/7.11 Flag 3).
The voltage is approx. +5VDC.
YN
Replace the Tray Module PWB (PL 14.7/PL 15.9).
Measure the voltage between the Tray Module PWB P/J549-24 (+) and GND (-) (BSD 7.9
Flag 2/7.11 Flag 2).
Activate the actuator of the Tray 2 Level Sensor (PL 2.3). The voltage changes.
YN
Replace the Tray 2 Level Sensor (PL 14.3/PL 15.6).
Replace the Tray Module PWB (PL 14.7/PL 15.9).
Check the paper transport drives and repair as required (PL 2.3, PL 14.7, PL 15.9).

Xerox WorkCentre 7132 Specifications

General

Brand	Xerox
Model	WorkCentre 7132
Category	All in One Printer
Language	English