Xerox WorkCentre 7132 Service Documentation

January 2007
4-2
WorkCentre 7132
Reversion 4.0
Repairs/Adjustments
REP 16.9.1 Compiler Tray Assembly.............................................................................. 4-177
REP 16.10.1 Stacker Motor Assembly............................................................................ 4-179
REP 16.10.2 Elevator Belt Assembly.............................................................................. 4-181
REP 16.11.1 Paddle Gear Shaft ..................................................................................... 4-182
REP 16.12.1 Finisher PWB............................................................................................. 4-184
REP 16.12.2 Finisher LVPS PWB................................................................................... 4-185
7. MPT
ADJ 7.1.1 MSI (Bypass) Tray Guide Adjustment ............................................................ 4-193
9. Xerographics
ADJ 9.1.0 Toner Density Adjustment .............................................................................. 4-195
ADJ 9.1.1 IOT Image Registration .................................................................................. 4-195
ADJ 9.1.2 Max Setup ...................................................................................................... 4-198
ADJ 9.1.6 TRC Adjustment............................................................................................. 4-199
ADJ 9.1.7 Color-To-Color Registration ........................................................................... 4-199
ADJ 9.1.8 IIT Calibration................................................................................................. 4-203
ADJ 9.1.9 Optical Axis Alignment ................................................................................... 4-205
ADJ 9.1.10 Procon ON/OFF Print ................................................................................... 4-206
ADJ 9.2.1 Edge Erase Value Adjustment ....................................................................... 4-211
ADJ 9.3.1 Software Loading and Upgrading................................................................... 4-211
11. IIT
ADJ 11.1.1 IIT Lead Edge/Side Edge Registration......................................................... 4-213
ADJ 11.1.2 IIT Vertical/Horizontal Magnification............................................................. 4-214
ADJ 11.2.1 Reduce/Enlarge Adjustment......................................................................... 4-215
ADJ 11.3.1 UI Alignment................................................................................................. 4-216
ADJ 11.6.1 Full/Half Rate Carriage Position Adjustment................................................ 4-217
15. DADF
ADJ 15.1.1 DADF Side Edge Registration...................................................................... 4-221
ADJ 15.1.3 DADF Non-Standard Sized Original Customized Registration Function...... 4-222
ADJ 15.1.4 DADF Lead Edge Registration..................................................................... 4-223
ADJ 15.1.5 DADF Height Adjustment ............................................................................. 4-225
ADJ 15.1.6 DADF Position (Skew) Adjustment............................................................... 4-226
22 a-finisher
REP 22.1 A-Finisher ....................................................................................................... 4-229
REP 22.3.1 Paddle Belt .................................................................................................. 4-230
REP 22.3.2 Sub Paddle Solenoid ................................................................................... 4-233
REP 22.4.1 Exit Roll Assembly....................................................................................... 4-234
REP 22.4.2 Staple Assembly.......................................................................................... 4-236
REP 22.4.3 Set Clamp Home Sensor ............................................................................. 4-237
REP 22.4.4 Exit Roll Assembly....................................................................................... 4-238
REP 22.5.1 Pinch Roll..................................................................................................... 4-240
REP 22.5.2 Finisher Entrance Sensor ............................................................................ 4-240
REP 22.5.3 Compile Exit Sensor .................................................................................... 4-242
REP 22.5.4 Main Paddle Shaft Assembly....................................................................... 4-243
REP 22.5.5 Lower Chute Assembly................................................................................ 4-245
REP 22.6.1 ENT Roll Assembly...................................................................................... 4-247
REP 22.6.2 Upper Chute Assembly................................................................................ 4-249
REP 22.7.1 Finisher Control PWB .................................................................................. 4-251
REP 22.8.1 Stacker Tray Assembly................................................................................ 4-251
REP 22.8.2 Stacker Shaft Assembly............................................................................... 4-253
REP 22.8.3 Stacker Motor............................................................................................... 4-255
REP 22.8.4 Stacker Stack Sensor .................................................................................. 4-257
REP 22.9.1 Compile Assembly ....................................................................................... 4-257
REP 22.9.2 Set Clamp Shaft........................................................................................... 4-259
REP 22.9.3 Eject Belt...................................................................................................... 4-261
REP 22.9.4 Eject/Set Clamp Motor Assembly ................................................................ 4-262
REP 22.9.5 Rear Tamper Home Sensor......................................................................... 4-264
REP 22.9.6 Eject Shaft Assembly................................................................................... 4-266
REP 22.10.1 Front /Rear Tamper Motor Assembly......................................................... 4-267
REP 22.10.2 Front Tamper Home Sensor ...................................................................... 4-269
REP 22.10.3 Eject Clamp Home Sensor......................................................................... 4-270
REP 22.10.4 Stack Height Sensor.................................................................................. 4-271

Xerox WorkCentre 7132 Specifications

General

Brand	Xerox
Model	WorkCentre 7132
Category	All in One Printer
Language	English