Xerox WorkCentre 7132 - Page 1461

January 2007
6-138
WorkCentre 7132
Controller & Fax NVM List
Reversion 4.0
General procedures information
Chain 790-xxx Chain 810-xxx Copy Service
790-670 Blank Document Detection Fea-
ture Display Settings
0, 1 0: Do not dis-
play
Read/
Write
0: Do not display
1: Display
790-671 Auto Resume Feature Settings 0, 1 1: Auto
Resume
Read/
Write
0: Do not Auto Resume
1: Auto Resume
790-672 Auto Clear Time-Out Display
Screen
0, 1 1: Follow M/C
configuration
Read/
Write
0: Maintain previous service
1: Follow M/C configuration
790-674 Basic FAX favorite setting
(2nd row)
0~255 0: Not set Read/
Write
0: Not set,
1: 2 Sided Document Feed,
2: Monitor Report,
3: Communication Mode,
4: Send Header
790-676 Separator Tray Default for Build
Separator Insertion
1~8 5: SMH Read/
Write
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
790-677 Side1 Cover Tray Default for
Cover
1~8 5: SMH Read/
Write
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
790-678 Side2 Cover Tray Default for
Cover
1~8 5: SMH Read/
Write
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
790-679 Side1 Cover Tray Default for
Booklet
1~8 5: SMH Read/
Write
1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF), 7: Tray 7 (HCF),
8: Interposer
790-680 Fax Number Double Input
Restriction
0, 1 0: Do not allow
double input
Read/
Write
0: Do not allow double input
1: Allow double input
790-682 Separator Sheet Default Tray
Setting
0~8 5: SMH Read/
Write
0: Auto, 1: Tray 1, 2: Tray 2, 3: Tray 3, 4: Tray 4, 5: SMH, 6: Tray 6 (HCF),
7: Tray 7 (HCF), 8: Interposer
Refer to the FF of Copy Service Func for the setup range.
790-683 Brightness/Contrast Settings -127
~127
0 Read/
Write
-127~127
(Because the valid range for each MCW Panel is different, the upper and lower limit values are con-
trolled through the UI Panel)
790-684 UI Screen Default Shortcut
Screen Settings
0, 1 0: Do not dis-
play anything
Read/
Write
0: Do not display anything, 1: Display login screen
Table 8 UI
Chain-Link NVM Name
Setup
Range Initial Value
Read/
Write Description
Table 9 Copy Service
Chain-Link NVM Name
Setup
Range
Initial Value Read/Write Description
790-600 Poster Overlap Width 1~25 10mm Read/Write 10mm~25mm
790-601 Index Paper Copy Image Shift
Amount
0~15 13mm Read/Write 0mm~15mm
790-602 Default Output Face 0~3 Auto Read/Write 0: Auto, 1: Output Side 2, 2: Output Side 1, 3: Output in reverse order
790-604 Single Copy Output Face
Switch
0, 1 Face Up Read/Write 0: Face Up, 1: Face Down
790-605 Sample Copy Default 0~1 0: Disable Sam-
ple Copy
Read/Write 0: Disable Sample Copy, 1: Enable Sample Copy