Keysight x-series Instruction Manual

6 Input/Output
6.1 RF Source
steps you have configured. For details see "Number of Steps" on page 1934
If you attempt to remotely set or query a subopcode that is out of range, an error is generated
Step Configuration Parameters
There are 10 parameters for each step, which must be in the following order in the
command:
1 Step Trigger
<step_trigger>
Data Type: enum
Specifies the input trigger for the step. For further details, see "Step Trigger" on
page 1935
2 Transition Time
<trans_time>
Data Type: enum
Specifies the transition time for the step, in seconds. For further details, see
"Transition Time" on page 1936
3 Radio Band
<band>
Data Type: enum
Specifies the radio band for the step, as any one of:
NONE | PGSM | EGSM | RGSM | DCS1800 | PCS1900 | TGSM810 |
GSM450 | GSM480 | GSM700 | GSM850 | BANDI | BANDII | BANDIII |
BANDIV | BANDV | BANDVI | BANDVII | BANDVIII | BANDIX | BANDX |
BANDXI | BANDXII | BANDXIII | BANDXIV | BANDXIX | USCELL |
USPCS | JAPAN | KOREAN | NMT | IMT2K | UPPER | SECOND | PAMR400
| PAMR800 | IMTEXT | PCS1DOT9G | AWS | US2DOT5G | PUBLIC |
LOWER | NONE | BAND1 | BAND2 | BAND3 | BAND4 | BAND5 | BAND6 |
BAND7 | BAND8 | BAND10 | BAND11 | BAND12 | BAND13 | BAND14 |
BAND17 | BAND18 | BAND19 | BAND20 | BAND21 | BAND24 | BAND25 |
BAND26 | BAND33 | BAND34 | BAND35 | BAND36 | BAND37 | BAND38 |
BAND39 | BAND40 | BAND41 | BAND42 | BAND43 | BANDA | BANDB |
BANDC | BANDD | BANDE | BANDF | N1 | N2 | N3 | N5 | N7 | N8 |
N12 | N20 | N25 | N28 | N34 | N38 | N39 | N40 | N41 | N50 | N51
| N66 | N70 | N71 | N74 | N75 | N76 | N77 | N78 | N79 | N80 |
N81 | N82 | N83 | N84 | N86 | N257 | N258 | N260 | N261
For further details, see "Band" on page 1937
4 Radio Band Link
<link_type>
Data Type: enum
Specifies the radio band link direction for the step, as either of:
DOWN|UP
For further details, see "Device" on page 1941
The old Device BTS|MS is obsolete, but is still supported, acting as an alias for the
Link parameter
5 Frequency/Channel
Number
<freq_chan>
Data Type: freq/chan num
Specifies the frequency in Hz or the channel number for the step. The channel
number and frequency are combined as one parameter that represents the
frequency or channel number depending on the radio band setting. If the radio band
is set to NONE, this value is interpreted as a frequency value in Hz. If the radio band
is set to a valid band, this value is interpreted as a channel number
For further details, see "Freq/Chan" on page 1942
Short Range Comms & IoT Mode User's &Programmer's Reference 1948

Keysight x-series Specifications

General

Analysis Bandwidth	Up to 1 GHz (depending on model)
Real-Time Bandwidth	Up to 1 GHz (depending on model)
Form Factor	Benchtop
Connectivity	LAN, USB, GPIB
Resolution Bandwidth	1 Hz to 10 MHz (depending on model)