OmniSwitch 6250 CLI Reference Guide November 2009 page 11 RDP Commands
no ipv6 neighbor ipv6_address {if_name}
ipv6 prefix ipv6_address /prefix_length if_name
[valid-lifetime time]
[preferred-lifetime time]
[on-link-flag {true | false}
[autonomous-flag {true | false}] if_name
no ipv6 prefix ipv6_address /prefix_length if_name
ipv6 route ipv6_prefix/prefix_length ipv6_address
[if_name]
no ipv6 route ipv6_prefix/prefix_length ipv6_address [if_name]
ipv6 static-route ipv6_prefix/prefix_length gateway ipv6_address [if_name] [metric metric]
no ipv6 static-route ipv6_prefix/prefix_length gateway ipv6_address [if_name]
ipv6 route-pref {static | rip} value
ping6 {ipv6_address | hostname} [if_name] [count count] [size data_size] [interval seconds]
traceroute6 {ipv6_address | hostname} [if_name] [max-hop hop_count] [wait-time time]
[port port_number] [probe-count probe]
show ipv6 hosts [substring]
show ipv6 icmp statistics [if_name]
show ipv6 interface [if_name | loopback]
show ipv6 pmtu table
clear ipv6 pmtu table
show ipv6 neighbors [ipv6_prefix/prefix_length | if_name | hw hardware_address | static]
clear ipv6 neighbors
show ipv6 prefixes
show ipv6 routes [ipv6_prefix/prefix_length | static]
show ipv6 route-pref
show iv6p router database [protocol type | gateway ipv6_address | dest ipv6_prefix/
prefix_length]
show ipv6 tcp ports
show ipv6 traffic [if_name]
clear ipv6 traffic
show ipv6 udp ports
show ipv6 information
ipv6 redist {local | static | rip} into {rip} route-map route-map-name
[status {enable | disable}]
ipv6 access-list access-list-name
no ipv6 access-list access-list-name
ipv6 access-list access-list-name
address address/prefixLen [action {permit | deny}]
[redist-control {all-subnets | no-subnets | aggregate}]
no ipv6 access-list access-list-name address address/prefixLen
show ipv6 redist [rip]
show ip access-list [access-list-name]
ipv6 load rip
ipv6 rip status {enable | disable}
ipv6 rip invalid-timer seconds
ipv6 rip garbage-timer seconds
ipv6 rip holddown-timer seconds
ipv6 rip jitter value
ipv6 rip route-tag value
ipv6 rip update-interval seconds
ipv6 rip triggered-sends {all | updated-only | none}
ipv6 rip interface if_name
[no] ipv6 rip interface if_name
ipv6 rip interface if_name metric value
ipv6 rip interface if_name recv-status {enable | disable}
ipv6 rip interface if_name send-status {enable | disable}
ipv6 rip interface if_name horizon {none | split-only | poison}
show ipv6 rip
show ipv6 rip interface [if_name]
show ipv6 rip peer [ipv6_addresss]
show ipv6 rip routes [dest <ipv6_prefix/prefix_length>] | [gateway <ipv6_addr>] | [detail
<ipv6 prefix/prefix_length>]
RDP Commands
ip router-discovery {enable | disable}
ip router-discovery interface name [enable | disable]
no router-discovery interface name
ip router-discovery interface name advertisement-address {all-systems-multicast | broadcast}
ip router-discovery interface name max-advertisement-interval seconds
ip router-discovery interface name min-advertisement-interval seconds
ip router-discovery interface name advertisement-lifetime seconds
ip router-discovery interface name preference-level level
show ip router-discovery
show ip router-discovery interface [name
]
DHCP Relay Commands
ip helper address ip_address
ip helper no address [ip_address]
ip helper address ip_address vlan vlan_id
ip helper no address ip_address vlan vlan_id
ip helper standard
ip helper per-vlan only
ip helper forward delay seconds
ip helper maximum hops hops
ip helper agent-information {enable | disable}
ip helper agent-information policy {drop | keep | replace}
ip helper pxe-support {enable | disable}
To Next Page
Loading...
