Distributed Spanning Tree Commands
OmniSwitch 6250 CLI Reference Guide November 2009 page 16-141
-> bridge mode 1x1
-> show spantree ports
Vlan Port Oper Status Path Cost Role
-----+-----+------------+---------+-----
1 1/1 DIS 0 DIS
1 1/2 DIS 0 DIS
1 1/3 DIS 0 DIS
1 1/4 DIS 0 DIS
1 1/5 DIS 0 DIS
1 1/6 DIS 0 DIS
1 1/7 DIS 0 DIS
1 1/8 DIS 0 DIS
1 1/9 DIS 0 DIS
1 1/10 DIS 0 DIS
1 1/11 DIS 0 DIS
1 1/12 FORW 19 ROOT
-> show spantree 1 ports
Spanning Tree Port Summary for Vlan 1
Oper Path Desig Prim. Op Op
Port St Cost Cost Role Port Cnx Edg Desig Bridge ID
-----+----+-------+-------+----+----+---+----+----------------------
1/1 DIS 0 0 DIS 1/1 NS EDG 0000-00:00:00:00:00:00
1/2 DIS 0 0 DIS 1/2 NS NO 0000-00:00:00:00:00:00
1/3 DIS 0 0 DIS 1/3 NS NO 0000-00:00:00:00:00:00
1/4 DIS 0 0 DIS 1/4 NS NO 0000-00:00:00:00:00:00
1/5 DIS 0 0 DIS 1/5 NS NO 0000-00:00:00:00:00:00
1/6 DIS 0 0 DIS 1/6 NS NO 0000-00:00:00:00:00:00
1/7 DIS 0 0 DIS 1/7 NS NO 0000-00:00:00:00:00:00
1/8 DIS 0 0 DIS 1/8 NS NO 0000-00:00:00:00:00:00
1/9 DIS 0 0 DIS 1/9 NS NO 0000-00:00:00:00:00:00
1/10 DIS 0 0 DIS 1/10 NS NO 0000-00:00:00:00:00:00
1/11 DIS 0 0 DIS 1/11 NS NO 0000-00:00:00:00:00:00
1/12 FORW 19 0 ROOT 1/12 PTP NO 0001-00:d0:95:6a:79:50
-> show spantree 1 ports active
Spanning Tree Port Summary for Vlan 1
Oper Path Desig Prim. Op Op
Port St Cost Cost Role Port Cnx Edg Desig Bridge ID
-----+----+-------+-------+----+----+----+---+----------------------
1/12 FORW 19 0 ROOT 1/12 PTP EDG 0001-00:d0:95:6a:79:50
output definitions
Vlan The VLAN ID associated with the VLAN Spanning Tree instance.
Configured through the vlan commands
Port The slot number for the module and the physical port number or a logi-
cal port. If the slot number is 0, then the port number refers to a link
aggregate logical port number (e.g., 0/31).
Oper St The port operational state as defined by application of the Spanning
Tree Protocol. Possible port operational states include: disabled, block-
ing, listening, learning, and forwarding.
Path Cost The contribution of this port to the path cost towards the Spanning Tree
root bridge that includes this port. Path cost is a measure of the distance
of the listed port from the root bridge in the number of hops. Config-
ured through the bridge slot/port path cost command.
To Next Page
Loading...
