Parameter
List of parameters
1-156
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Description: Sets the simulation mode for digital inputs.
Dependency: The setpoint for the input signals is specified using p0796.
Refer to: p0796
Notice: If a digital input is used as signal source for the function "STO" (BI: p9620) then it is not permissible to select the
simulation mode and this is rejected.
Note: This parameter is not saved when data is backed-up (p0971, p0977).
DI: Digital Input
DI/DO: Bidirectional Digital Input/Output
Description: Sets the setpoint for the input signals in the digital input simulation mode.
p0795 CU digital inputs simulation mode / CU DI simulation
CU_S110-CAN,
CU_S110-DP,
CU_S110-PN
Can be changed: U, T Calculated: - Access level: 2
Data type: Unsigned32 Dynamic index: - Func. diagram: 1510, 2020,
2030, 2031, 2100, 2120, 2130,
2131, 2132, 2133
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0000 0000 0000 0000 0000
0000 0000 0000 bin
Bit field: Bit Signal name 1 signal 0 signal FP
00 DI 0 (X133.1) Simulation Terminal eval. -
01 DI 1 (X133.2) Simulation Terminal eval. -
02 DI 2 (X133.3) Simulation Terminal eval. -
03 DI 3 (X133.4) Simulation Terminal eval. -
08 DI/DO 8 (X132.1) Simulation Terminal eval. -
09 DI/DO 9 (X132.2) Simulation Terminal eval. -
10 DI/DO 10 (X132.3) Simulation Terminal eval. -
11 DI/DO 11 (X132.4) Simulation Terminal eval. -
16 DI 16 (X130.1) Simulation Terminal eval. -
17 DI 17 (X130.2) Simulation Terminal eval. -
18 DI 18 (X130.4) Simulation Terminal eval. -
19 DI 19 (X130.5) Simulation Terminal eval. -
20 DI 20 (X131.1) Simulation Terminal eval. -
21 DI 21 (X131.2) Simulation Terminal eval. -
22 DI 22 (X131.4) Simulation Terminal eval. -
p0796 CU digital inputs simulation mode setpoint / CU DI simul setp
CU_S110-CAN,
CU_S110-DP,
CU_S110-PN
Can be changed: U, T Calculated: - Access level: 2
Data type: Unsigned32 Dynamic index: - Func. diagram: 1510, 2020,
2030, 2031, 2100, 2120, 2130,
2131, 2132, 2133
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0000 0000 0000 0000 0000
0000 0000 0000 bin
Bit field: Bit Signal name 1 signal 0 signal FP
00 DI 0 (X133.1) High Low -
01 DI 1 (X133.2) High Low -
02 DI 2 (X133.3) High Low -
03 DI 3 (X133.4) High Low -
08 DI/DO 8 (X132.1) High Low -
09 DI/DO 9 (X132.2) High Low -
10 DI/DO 10 (X132.3) High Low -
11 DI/DO 11 (X132.4) High Low -
16 DI 16 (X130.1) High Low -
17 DI 17 (X130.2) High Low -
To Next Page
Loading...
