Siemens SINAMICS S110 - p20138 BI: MFP 0 input pulse I; MFP 0 inp_pulse I; p20139 MFP 0 pulse duration in ms; MFP 0 pulse_dur ms; r20140 BO: MFP 0 output Q; MFP 0 output Q; p20141 MFP 0 run-time group; MFP 0 RTG

List of parameters
Parameter
1-687
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
Description: Sets the signal source for the input pulse I of instance MFP 0 of the pulse generator.
Description: Setting parameter for pulse duration T in milliseconds of instance MFP 0 of the pulse generator.
Description: Display parameter for output pulse Q of instance MFP 0 of the pulse generator.
Description: Setting parameter for the run-time group in which the instance MFP 0 of the pulse generator is to be called.
Value: 0: Run-time group 0
1: Run-time group 1
2: Run-time group 2
p20138 BI: MFP 0 input pulse I / MFP 0 inp_pulse I
CU_S110-CAN,
CU_S110-DP,
CU_S110-PN,
SERVO_S110-CAN
(FBLOCKS),
SERVO_S110-DP
(FBLOCKS),
SERVO_S110-PN
(FBLOCKS)
Can be changed: T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dynamic index: - Func. diagram: 7230
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0
p20139 MFP 0 pulse duration in ms / MFP 0 pulse_dur ms
CU_S110-CAN,
CU_S110-DP,
CU_S110-PN,
SERVO_S110-CAN
(FBLOCKS),
SERVO_S110-DP
(FBLOCKS),
SERVO_S110-PN
(FBLOCKS)
Can be changed: T Calculated: - Access level: 1
Data type: FloatingPoint32 Dynamic index: - Func. diagram: 7230
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0.00 60000.00 0.00
r20140 BO: MFP 0 output Q / MFP 0 output Q
CU_S110-CAN,
CU_S110-DP,
CU_S110-PN,
SERVO_S110-CAN
(FBLOCKS),
SERVO_S110-DP
(FBLOCKS),
SERVO_S110-PN
(FBLOCKS)
Can be changed: - Calculated: - Access level: 1
Data type: Unsigned32 Dynamic index: - Func. diagram: 7230
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - -
p20141 MFP 0 run-time group / MFP 0 RTG
CU_S110-CAN,
CU_S110-DP,
CU_S110-PN,
SERVO_S110-CAN
(FBLOCKS),
SERVO_S110-DP
(FBLOCKS),
SERVO_S110-PN
(FBLOCKS)
Can be changed: T Calculated: - Access level: 1
Data type: Integer16 Dynamic index: - Func. diagram: 7230
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0 9999 9999