Parameter
Parameters for data sets
1-736
© Siemens AG 2012 All Rights Reserved
SINAMICS S110 List Manual (LH7), 06/2012, 6SL3097-4AP10-0BP3
p1082[0...n] Maximum speed / n_max
p1083[0...n] CO: Speed limit in positive direction of rotation / n_limit pos
p1086[0...n] CO: Speed limit in negative direction of rotation / n_limit neg
p1091[0...n] Skip speed 1 / n_skip 1
p1092[0...n] Skip speed 2 / n_skip 2
p1093[0...n] Skip speed 3 / n_skip 3
p1094[0...n] Skip speed 4 / n_skip 4
p1101[0...n] Skip speed bandwidth / n_skip bandwidth
p1120[0...n] Ramp-function generator ramp-up time / RFG ramp-up time
p1121[0...n] Ramp-function generator ramp-down time / RFG ramp-down time
p1130[0...n] Ramp-function generator initial rounding-off time / RFG t_start_round
p1131[0...n] Ramp-function generator final rounding-off time / RFG t_end_delay
p1134[0...n] Ramp-function generator rounding-off type / RFG round-off type
p1135[0...n] OFF3 ramp-down time / OFF3 t_RD
p1136[0...n] OFF3 initial rounding-off time / RFGOFF3 t_strt_rnd
p1137[0...n] OFF3 final rounding-off time / RFG OFF3 t_end_del
p1145[0...n] Ramp-function generator tracking intensity. / RFG track intens
p1148[0...n] Ramp-function gen., tolerance for ramp-up and ramp-down active / RFG tol HL/RL act
p1151[0...n] Ramp-function generator configuration / RFG config
p1189[0...n] Speed setpoint configuration / n_ctrl config
p1192[0...n] DSC enc selection / DSC enc selection
p1193[0...n] DSC encoder adaptation factor / DSC encodAdaptFact
p1226[0...n] Threshold for zero speed detection / n_standst n_thresh
p1240[0...n] Vdc controller or Vdc monitoring configuration / Vdc_ctrl config
p1244[0...n] DC link voltage threshold upper / Vdc upper thresh
p1248[0...n] DC link voltage threshold lower / Vdc lower thresh
p1250[0...n] Vdc controller proportional gain / Vdc_ctrl Kp
p1300[0...n] Open-loop/closed-loop control operating mode / Op/cl-lp ctrl_mode
p1317[0...n] U/f control activation / Uf act
p1318[0...n] U/f control ramp-up/ramp-down time / Uf t_rmp-up_rmp-dn
p1319[0...n] U/f control voltage at zero frequency / Uf U at f=0 Hz
p1326[0...n] U/f control characteristic frequency / Uf char f4
p1327[0...n] U/f control characteristic voltage / Uf char U4
p1338[0...n] U/f mode resonance damping gain / Uf Res_damp gain
p1339[0...n] U/f mode resonance damping filter time constant / Uf Res_damp T
p1345[0...n] DC braking proportional gain / DCBRK Kp
p1346[0...n] DC braking, integral time / DCBRK Tn
p1349[0...n] U/f mode resonance damping maximum frequency / Uf res_damp f_max
p1400[0...n] Speed control configuration / n_ctrl config
p1402[0...n] Closed-loop current control and motor model configuration / I_ctrl config
p1404[0...n] Encoderless operation changeover speed / Encoderl op n_chg
p1414[0...n] Speed setpoint filter activation / n_set_filt act
p1415[0...n] Speed setpoint filter 1 type / n_set_filt 1 typ
p1416[0...n] Speed setpoint filter 1 time constant / n_set_filt 1 T
p1417[0...n] Speed setpoint filter 1 denominator natural frequency / n_set_filt 1 fn_d
p1418[0...n] Speed setpoint filter 1 denominator damping / n_set_filt 1 D_d
p1419[0...n] Speed setpoint filter 1 numerator natural frequency / n_set_filt 1 fn_n
p1420[0...n] Speed setpoint filter 1 numerator damping / n_set_filt 1 D_n
p1428[0...n] Speed pre-control balancing dead time / n_prectrBal t_dead
p1429[0...n] Speed pre-control balancing time constant / n_prectr bal T
p1433[0...n] Speed controller reference model natural frequency / n_ctrl RefMod fn
p1434[0...n] Speed controller reference model damping / n_ctrl RefMod D
p1435[0...n] Speed controller reference model dead time / n_ctrRefMod t_dead
To Next Page
Loading...
