Keysight Technologies InfiniiVision 4000 X Series User Manual

1746 Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Index
arming edge source, Edge Then Edge
trigger, 1313
arrange waveforms, 1505
ASCII format, 1405
ASCII format for data transfer, 1399
ASCII string, quoted, 224
ASCiixy waveform data format, 846
assign channel names, 352
attenuation factor (external trigger)
probe, 435
attenuation for oscilloscope probe, 354
audio channel, I2S trigger, 955
AUT option for probe sense, 1503, 1507
Auto Range capability for DVM, 428
auto set up, trigger level, 1305
auto set up, USB 2.0 signal quality
test, 368
auto setup (ARINC 429), 860
auto setup for M1553 trigger, 993
auto setup for power analysis signals, 776
auto trigger sweep mode, 1295
automask create, 671
automask source, 672
automask units, 673
automatic measurements constants, 354
automatic probe type detection, 1503,
1507
autoscale, 261
autoscale acquire mode, 263
autoscale channels, 264
AUToscale command, 82
autoset for FLEXray event trigger, 936
autosetup for FLEXray decode, 926
average math function, clear, 468
average value measurement, 585, 629
Average, power modulation analysis, 753
averaged value math function, 491
averaging acquisition type, 300, 1397
averaging, synchronizing with, 1596
Ax + B math function, 491
B
backlight, display, 410
bandwidth filter limits, 434
bandwidth filter limits to 20 MHz, 347
bar chart of current harmonics results, 737
BARTlett window, 483
base 10 exponential math function, 491
base value measurement, 586, 630
base, ARINC 429, 861
base, I2S serial decode, 947
base, MIL-STD-1553 serial decode, 994
base, SENT decode, 1042
base, UART trigger, 1105
base, USB decode, 1115
basic instrument functions, 231
baud rate, 890, 978, 1094
baud rate, CAN FD, 892
baud rate, user-defined, ARINC 429, 862
begin acquisition, 268, 291, 293
BHARris window for minimal spectral
leakage, 483
Bin Size, FFT, 470
binary block data, 224, 412, 521, 1277,
1403
BINary waveform data format, 846
bind levels for masks, 692
bit order, 1095
bit order, SPI decode, 1075
bit rate measurement, 572
bit selection command, bus, 323
bit weights, 236
bitmap display, 412, 522
bits in Service Request Enable
Register, 249
bits in Standard Event Status Enable
Register, 234
bits in Status Byte Register, 251
bits selection command, bus, 324
blank, 266
block data, 224, 239, 1277
block response data,
86
blocking commands, 91
blocking synchronization, 1591
blocking synchronization example, 1598
blocking wait, 1590
BMP format screen image data, 412, 522
braces, 223
built-in measurements, 79
burst data demo signal, 387
burst width measurement, 573
burst, minimum time before next, 1320
bus bit selection command, 323
bus bits selection commands, 324
bus clear command, 326
bus commands, 322
BUS data format, 1400
bus display, 327
bus label command, 328
bus mask command, 329
BUS<n> commands, 321
button disable, 1265
button, calibration protect, 337
byte format for data transfer, 1399, 1405
BYTeorder, 1401
C
C, SICL library example, 1706
C, VISA library example, 1653
C#, SCPI.NET example, 1726
C#, VISA COM example, 1629
C#, VISA example, 1672
CAL PROTECT button, 337
CAL PROTECT switch, 332
calculating preshoot of waveform, 606
calculating the waveform overshoot, 600
calibrate, 333, 334, 337, 341
CALibrate commands, 331
calibrate date, 333
calibrate introduction, 332
calibrate label, 334
calibrate output, 335
calibrate start, 338
calibrate status, 339
calibrate switch, 337
calibrate temperature, 340
calibrate time, 341
CAN acknowledge, 889
CAN and LIN demo signal, 388
CAN baud rate, 890
CAN demo signal, 387
CAN FD baud rate, 892
CAN FD data triggers, starting byte
position, 901
CAN frame counters, reset, 882
CAN SEARch commands, 1186
CAN serial bus commands, 877
CAN serial search, data, 1189
CAN serial search, data length, 1190
CAN serial search, ID, 1191
CAN serial search, ID mode, 1192
CAN serial search, mode, 1187
CAN signal definition, 891
CAN source, 893
CAN symbolic data display, 886
CAN symbolic data, recall, 813
CAN trigger, 894, 900
CAN trigger data pattern, 898
CAN trigger ID pattern, 902
CAN trigger pattern id mode, 903
CAN trigger, ID filter for, 897
CAN triggering, 854
capture data, 268
capturing data, 78
cardiac waveform generator output, 1448
center frequency set, 471, 490
center of screen, 1430
center screen, vertical value at, 489, 495
center time base reference, 1287
CFD demo signal, 389
channel, 297, 352, 1498, 1500
channel coupling, 348
channel display, 349
channel input impedance, 350
channel inversion, 351
channel label, 352, 1499
channel labels, 418, 419
channel numbers, 1505
channel overload, 362
Channel Power, FFT analysis
measurement, 592
channel protection, 362
channel reset conditions, 244, 1266
channel selected to produce trigger, 1338,
1380
channel signal type, 360
channel skew for oscilloscope probe, 359,
1501
channel status, 294, 1505
channel threshold, 1500
channel vernier, 366
channel, stop displaying, 266

Keysight Technologies InfiniiVision 4000 X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 4000 X Series
Category	Test Equipment
Language	English