Keysight Technologies InfiniiVision 4000 X Series User Manual

1748 Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Index
CSV (Comma Separated Values) waveform
data format, 846
CT bits (CXPI), triggering on, 921
cumulative edge activity, 1498
current harmonics analysis fail count, 738
current harmonics analysis results,
save, 836
current harmonics analysis run count, 743
current harmonics analysis, apply, 735
current harmonics results data, 736
current harmonics results display, 737
current logic levels on digital
channels, 259
current oscilloscope configuration, 239,
243, 247, 1277
current probe, 365, 437
CURRent segment waveform save
option, 849
current source, 793
cursor display setting, X1, 532
cursor display setting, X2, 535
cursor display setting, Y1, 541
cursor display setting, Y2, 543
cursor mode, 531
cursor position, 530, 533, 536, 538, 542,
545
cursor readout, 1520, 1524, 1525
cursor reset conditions, 244, 1266
cursor source, 534, 537
cursor time, 1520, 1524, 1525
cursor units, X, 539, 540
cursor units, Y, 546, 547
cursor values, saving, 839
cursors track measurements, 613
cursors, how autoscale affects, 261
cursors, X1, X2, Y1, Y2, 529
custom time base reference,
1287
custom time base reference location, 1288
CXPI demo signal, 388
CXPI frame data value, 917
CXPI partiy bit display, 910
CXPI serial bus commands, 907
CXPI signal baud rate, 909
CXPI signal source, 911
CXPI signal tolerance, 912
CXPI trigger mode, 913
CXPI triggering, 854
cycle count base, FLEXray frame
trigger, 939
cycle count repetition, FLEXray frame
trigger, 940
cycle measured, 589, 596
cycle time, 603
cycles analyzed, number of, 777, 778
D
D- source, USB 2.0 signal quality test, 373
D- USB signal source, 1116
D+ source, USB 2.0 signal quality test, 374
D+ USB signal source, 1117
data, 966, 968, 1403
data (waveform) maximum length, 848
data 2, 969
data acquisition types, 1396
data conversion, 1398
data format for transfer, 1398
data length, USB search, 1247
data length, USB trigger, 1124
data output order, 1401
data pattern length, 900, 987
data pattern, ARINC 429 trigger, 871,
1183
data pattern, CAN trigger, 898
data PID, USB search, 1252
data PID, USB trigger, 1130
data point index, 1427
data points, 308
data record, measurement, 1408
data record, raw acquisition, 1408
data required to fill time buckets, 303
DATA source, I2S, 951
data source, setup and hold trigger, 1368
data structures, status reporting, 1559
data value, USB search, 1246
data value, USB trigger, 1123
data, saving and recalling, 403
date, calibration, 333
date, system, 1261
DC coupling for edge trigger, 1325
DC input coupling for specified
channel, 348
DC offset correction for integrate
input, 486
DC RMS measured on waveform, 588, 635
DC waveform generator output, 1447
DCMotor demo signal, 389
DDE (Device Dependent Error) status
bit, 234, 236
decision chart, status reporting, 1580
default conditions, 244, 1266
define channel labels, 352
define delay measurement parameters, 582
define glitch trigger, 1336
define logic thresholds, 1500
define measurement, 578
define measurement source, 615
define trigger, 1337, 1356, 1357, 1359
defined as, 223
definite-length block query response, 86
definite-length block response data, 224
delay bits, SPI MISO stream, 1078
delay measured to calculate phase, 604
delay measurement, 578, 580
delay measurement parameters,
define, 582
delay measurements, 624
delay time, Edge Then Edge trigger, 1314
DELay trigger commands, 1311
delay, how autoscale affects, 261
delayed time base, 1283
delayed window horizontal scale, 1293
delete mask, 681
delta time, 1520
delta voltage measurement, 1528
delta X cursor, 529
delta Y cursor, 529
demo, 385
DEMO commands, 385
demo signal, 387
demo signal function, 386
demo signal phase angle, 391
demo signals output control, 392
deskew for power measurements, 731
destination, remote command
logging, 1271
detecting probe types, 1503, 1507
Device Clear to abort a sequential (blocking)
command, 92
device-defined error queue clear, 233
DIFF source for function, 1511
differences from 3000 X-Series oscilloscope
commands, 63
differential D+ and D- USB signal
source, 1118
differential probe heads, 355
differential probe source, USB 2.0 signal
quality test, 372
differential signal type, 360
differentiate math function, 305, 490,
1417
digital channel commands, 394, 395, 396,
397, 399
digital channel data, 1400
digital channel labels, 419
digital channel order, 1505
digital channel source for glitch
trigger, 1338
digital channels, 6
digital channels, activity and logic levels
on, 259
digital channels, groups of, 699, 701, 703
digital pod, stop displaying, 266
digital reset conditions, 245, 1267
DIGital<d> commands, 393
digitize channels, 268
DIGitize command, 78, 83, 1396
Digitizer mode, 306
digits, 224
disable anti-alias mode, 305
disable front panel, 1265
disable function, 1512
disabling calibration, 337
disabling channel display, 349
disabling status register bits, 234, 248
discontinued and obsolete
commands, 1491
display annotation, 404
display annotation background, 405
display annotation color, 406
display annotation text, 407
display channel labels, 418
display clear, 411
DISPlay commands, 401
display commands introduction, 403

Keysight Technologies InfiniiVision 4000 X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 4000 X Series
Category	Test Equipment
Language	English