Keysight Technologies InfiniiVision 4000 X Series User Manual

Index
Keysight InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1751
grid type, 416
groups of digital channels, 699, 701, 703,
1500
H
handshake PID, USB search, 1253
handshake PID, USB trigger, 1131
HANNing window for frequency
resolution, 483
hardcopy, 290, 504
HARDcopy commands, 503
hardcopy factors, 508, 829
hardcopy filename, 1514
hardcopy format, 1513
hardcopy formfeed, 509
hardcopy grayscale, 1515
hardcopy invert graticule colors, 510,
1516
hardcopy layout, 511
hardcopy palette, 518
hardcopy print, area, 506
hardcopy printer driver, 1517
Hardware Event Condition Register
(:HWERegister:CONDition), 272
Hardware Event Condition Register
(:OPERegister:CONDition), 1577
Hardware Event Enable Register
(HWEenable), 270
Hardware Event Event Register
(:HWERegister[:EVENt]), 273, 1576
HARMonics demo signal, 389
HCOPY commands, 503
head type, probe, 355
header, 1611
high pass filter math function, 491
high resolution acquisition type, 1398
high trigger level, 1306
high-frequency reject filter, 1300, 1327
high-level voltage, waveform
generator, 1478
high-pass filter cutoff frequency, 484
high-resolution acquisition type, 300
hold time, setup and hold trigger, 1369
hold until operation complete, 240
holdoff time, 1301
holes in waveform data, 1403
hop frequency, waveform generator FSK
modulation, 1457
horizontal adjustment, fine (vernier), 1290
horizontal position, 1291
horizontal scale, 1289, 1293
horizontal scaling, 1410
horizontal time, 1285,
1292, 1520
Host ID of oscilloscope, 1262
Host name softkey, 72
hostname, 72
hub address value, USB search, 1251
hub address value, USB trigger, 1128
hubs, USB 2.0 signal quality, 369
HWEenable (Hardware Event Enable
Register), 270
HWERegister:CONDition (Hardware Event
Condition Register), 272, 1577
HWERegister[:EVENt] (Hardware Event
Event Register), 273, 1576
I
I1080L50HZ, 1377, 1381
I1080L60HZ, 1377, 1381
I2C demo signal, 387
I2S alignment, 946
I2S audio channel, 955
I2S clock slope, 948
I2S CLOCk source, 950
I2S DATA source, 951
I2S demo signal, 388
I2S pattern data, 956
I2S pattern format, 958
I2S range, 959
I2S receiver width, 949
I2S SEARch commands, 1202
I2S serial bus commands, 943
I2S serial decode base, 947
I2S serial search, audio channel, 1203
I2S serial search, data, 1205
I2S serial search, format, 1206
I2S serial search, mode, 1204
I2S serial search, range, 1207
I2S transmit word size, 960
I2S trigger operator, 953
I2S triggering, 854
I2S word select (WS) low, 961
I2S word select (WS) source, 952
ID filter for CAN trigger, 897
id mode, 903
ID pattern, CAN trigger, 902
identification number, 238
identification of options, 241
identifier, LIN, 984
idle, 1320
idle state, SENT bus, 1046
idle until operation complete, 240
IDN (Identification Number), 238
IEC 61000-3-2 standard for current
harmonics analysis, 744
IEEE 488.2 standard, 231
IIC address, 967
IIC clock, 965
IIC data, 966, 968
IIC data 2, 969
IIC SEARch commands, 1208
IIC serial decode address field size, 964
IIC serial search, address, 1211
IIC serial search, data, 1212
IIC serial search, data2,
1213
IIC serial search, mode, 1209
IIC serial search, qualifier, 1214
IIC trigger commands, 962
IIC trigger qualifier, 970
IIC trigger type, 971
IIC triggering, 854
image format, 830
image invert graticule colors, 831
image memory, 294
image palette, 832
image, save, 828
image, save with inksaver, 831
impedance, 350
infinity representation, 1617
initial load current, transient response
analysis, 805
initialization, 78, 81
initialize, 244, 1266
initialize label list, 419
initiate acquisition, 268
inksaver, save image with, 831
input coupling for channels, 348
input for integrate, DC offset
correction, 486
input impedance for channels, 350, 1502
input inversion for specified channel, 351
input power, 653
input source, Control Loop Response (Bode)
power analysis, 725
input source, Power Supply Rejection Ratio
(PSRR) power analysis, 768
inrush current, 657
inrush current analysis, 747, 748, 749
inrush current expected, 785
insert label, 352
installed options identified, 241
instruction header, 1611
instrument number, 238
instrument options identified, 241
instrument requests service, 251
instrument serial number, 292
instrument settings, 504
instrument status, 88
instrument type, 238
integrate DC offset correction, 486
integrate math function, 490
, 1417
INTegrate source for function, 1511
intensity, waveform, 417
internal low-pass filter, 347, 434
introduction to :ACQuire commands, 300
introduction to :BUS<n> commands, 322
introduction to :CALibrate commands, 332
introduction to :CHANnel<n>
commands, 345
introduction to :COUNter commands, 379
introduction to :DEMO commands, 385
introduction to :DIGital<d>
commands, 394
introduction to :DISPlay commands, 403
introduction to :EXTernal commands, 433
introduction to :FRANalysis
commands, 440
introduction to :FUNCtion commands, 460
introduction to :HARDcopy
commands, 504
introduction to :LISTer commands, 523

Keysight Technologies InfiniiVision 4000 X Series Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision 4000 X Series
Category	Test Equipment
Language	English