R&S RTO6 - Page 1309

Remote control commands
R&S
®
RTO6
1309User Manual 1801.6687.02 ─ 05
<Source> C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2 |
C3W3 | C4W1 | C4W2 | C4W3
| M1 | M2 |
M3 | M4 | M5 | M6 |
M7 | M8 | R1 | R2 | R3 | R4 | XY1 | XY2 | XY3 | XY4 |
MRESult1 | MRESult2 | MRESult3 | MRESult4 | MRESult5 |
MRESult6 | MRESult7 | MRESult8 | QUICk | QUICK | SBUS1 |
SBUS2 | SBUS3 | SBUS4 | D0 | D1 | D2 | D3 | D4 | D5 | D6 |
D7 | D8 | D9 | D10 | D11 | D12 | D13 | D14 | D15 | MSOB1 |
MSOB2 | MSOB3 | MSOB4 | TRK1 | TRK2 | TRK3 | TRK4 |
TRK5 | TRK6 | TRK7 | TRK8 | SG1 | SG2 | SG3 | SG4 | SG5 |
SG6 | SG7 | SG8 | SG1TL1 | SG1TL2 | SG2TL1 | SG2TL2 |
SG3TL1 | SG3TL2 | SG4TL1 | SG4TL2 | SG5TL1 | SG5TL2 |
SG6TL1 | SG6TL2 | SG7TL1 | SG7TL2 | SG8TL1 | SG8TL2 |
Z1V1 | Z1V2 | Z1V3 | Z1V4 | Z1I1 | Z1I2 | Z1I3 | Z1I4 | Z2V1 |
Z2V2 | Z2V3 | Z2V4 | Z2I1 | Z2I2 | Z2I3 | Z2I4 | DIFF1 | DIFF2 |
COMMON1 | COMMON2
Waveform to that the label belongs, see Chapter 24.4.1, "Wave-
form suffix", on page 1279.
<LabelText> String with the label text that is shown on the display
<PositionMode> ABS | REL
ABS
Position in time and voltage values, or in other units depending
on the waveform character
. Absolute positions move with the
waveform display when the scales, the vertical position or of
fset,
or the reference point are changed.
REL
Fixed label position in percent of the screen counting from the
upper left corner.
<XPositon> Horizontal position of the label text. Values, range and unit
depend on the position mode, the waveform position and scal-
ing. For relative position mode, the range is 0 to 100 %.
<YPositon> Vertical position of the label text. Values, range and unit depend
on the position mode, the waveform position and scaling. For
relative position mode, the range is 0 to 100 %.
Usage: Setting only
Asynchronous command
DISPlay:SIGNal:LABel:REMove <LabelID>, <Source>
Deletes the specifies waveform label.
Setting parameters:
<LabelID> String with the label identifier.
<Source> All waveforms that can be displayed, see DISPlay:
SIGNal:
LABel:
ADD
Example:
DISPlay:SIGNal:LABel:REMove 'Label1', C1W1
Instrument setup