R&S RTO6 User Manual

Remote control commands
R&S
®
RTO6
1684User Manual 1801.6687.02 ─ 05
TRIGger<m>:I2C:DMIN <Data>
Specifies the data bit pattern, or sets the the start value of a data pattern range.. Enter
the bytes in msb first bit order
. The maximum pattern length is 64 bit. W
aveform data is
compared with the pattern byte-by-byte.
Parameters:
<Data> Numeric or string pattern, see Chapter 24.4.6, "Bit pattern
parameter", on page 1286. The string parameter accepts the bit
value X (don't care).
Usage: Asynchronous command
TRIGger<m>:I2C:DMAX <DataTo>
Sets the the end value of an data range if TRIGger<m>:
I2C:DCONdition is set to
INRange or OORange.
Parameters:
<DataTo> Numeric or string pattern, see Chapter 24.4.6, "Bit pattern
parameter", on page 1286. The string parameter accepts the bit
value X (don't care).
Usage: Asynchronous command
24.17.3.3 Decode results
To load and acivate a label list, use:
●
BUS<m>:
NEWList on page 1672
●
BUS<m>:SYMBols on page 1672
BUS<m>:I2C:FRAMe<n>:DATA?...................................................................................1685
BUS<m>:I2C:FCOunt?................................................................................................. 1685
BUS<m>:I2C:FRAMe<n>:AACCess?.............................................................................1685
BUS<m>:I2C:FRAMe<n>:ACCess?............................................................................... 1686
BUS<m>:I2C:FRAMe<n>:ACOMplete?.......................................................................... 1686
BUS<m>:I2C:FRAMe<n>:ADBStart?............................................................................. 1686
BUS<m>:I2C:FRAMe<n>:ADDRess?.............................................................................1687
BUS<m>:I2C:FRAMe<n>:ADEVice?..............................................................................1687
BUS<m>:I2C:FRAMe<n>:AMODe?............................................................................... 1687
BUS<m>:I2C:FRAMe<n>:ASTart?................................................................................. 1688
BUS<m>:I2C:FRAMe<n>:BITRate?............................................................................... 1688
BUS<m>:I2C:FRAMe<n>:RWBStart?.............................................................................1688
BUS<m>:I2C:FRAMe<n>:STATus?................................................................................1689
BUS<m>:I2C:FRAMe<n>:STARt?..................................................................................1689
BUS<m>:I2C:FRAMe<n>:STOP?.................................................................................. 1690
BUS<m>:I2C:FRAMe<n>:SYMBol?............................................................................... 1690
BUS<m>:I2C:FRAMe<n>:BCOunt?............................................................................... 1690
BUS<m>:I2C:FRAMe<n>:BYTE<o>:ACCess?................................................................ 1691
BUS<m>:I2C:FRAMe<n>:BYTE<o>:ACKStart?...............................................................1691
Protocols

R&S RTO6 Specifications

General

Bandwidth	Up to 6 GHz
Sample Rate	Up to 20 Gsample/s
Memory Depth	Up to 2 Gsample
Channels	Up to 4
Vertical Sensitivity	1 mV/div to 10 V/div
Vertical Resolution	Up to 16 bit
Trigger Modes	Edge, Pulse
Interface	LAN, USB, GPIB
Input Impedance	50 Ω, 1 MΩ