Remote control commands
R&S
®
RTO6
1768User Manual 1801.6687.02 ─ 05
24.17.7.2 T
rigger
The trigger suf
fix <m> is always 1 and can be omitted. It selects the trigger event: Only
the A-trigger is available for triggering on serial buses.
To trigger on a serial bus, make sure that:
●
TRIGger<m>:SOURce[:SELect] is set to SBUS.
●
The sources of the serial bus are channel signals: use BUS<m>:...:SOURce
commands.
●
Decoding is enabled: BUS<m>[:STATe] is set to ON.
TRIGger<m>:CMSB:TYPE............................................................................................1768
TRIGger<m>:CMSB:PATTern........................................................................................1769
TRIGger<m>:CMSB:ICONdition.................................................................................... 1769
TRIGger<m>:CMSB:IMIN............................................................................................. 1769
TRIGger<m>:CMSB:IMAX............................................................................................ 1770
TRIGger<m>:CMSB:NRZ:WRDLength...........................................................................1770
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:ENABle....................................................... 1770
TRIGger<m>:CMSB:ADVanced:FRENable..................................................................... 1770
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:ENABle...........................................1770
TRIGger<m>:CMSB:ADVanced:FIENable.......................................................................1770
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:BIT.................................................1771
TRIGger<m>:CMSB:ADVanced:BIT............................................................................... 1771
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:DMAX.............................................1771
TRIGger<m>:CMSB:ADVanced:DMAX...........................................................................1771
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:DMIN..............................................1772
TRIGger<m>:CMSB:ADVanced:DMIN............................................................................1772
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:DOPerator...................................... 1772
TRIGger<m>:CMSB:ADVanced:DOPerator.....................................................................1772
TRIGger<m>:CMSB:ADVanced:ERRor<n>:ENABle........................................................ 1772
TRIGger<m>:CMSB:ADVanced:ERENable.....................................................................1772
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:IMAX.............................................. 1773
TRIGger<m>:CMSB:ADVanced:IMAX............................................................................ 1773
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:IMIN............................................... 1773
TRIGger<m>:CMSB:ADVanced:IMIN............................................................................. 1773
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:IOPerator........................................1773
TRIGger<m>:CMSB:ADVanced:IOPerator...................................................................... 1773
TRIGger<m>:CMSB:TYPE <Type>
Selects the trigger type for custom serial bus analysis.
Suffix:
<m>
.
1..3
Parameters:
<Type> STARt | PATTern | ADVanced
ST
ARt
T
riggers on the frame start, which is the end of the gap time as
specified in BUS<m>:CMSB:GAPTime:VALue on page 1762
Protocols
To Next Page
Loading...
