R&S RTO6 - 24.17.23.4 Search settings

Remote control commands
R&S
®
RTO6
2232User Manual 1801.6687.02 ─ 05
24.17.23.4 Search settings
The trigger suf
fix <m> is always 1 and can be omitted. It selects the trigger event: Only
the A-trigger is available for triggering on serial buses.
T
o trigger on a serial bus, make sure that:
●
TRIGger<m>:SOURce[:SELect] is set to SBUS.
●
The sources of the serial bus are channel signals: use BUS<m>:...:SOURce
commands.
●
Decoding is enabled: BUS<m>[:STATe] is set to ON.
There are two commands for each parameter, that you can use for defining the USBPD
settings.
For example, to set the Frame type =Control Frame > Field =MsgID >Data value you
can use one of the following commands:
●
SEARch:TRIGger:USBPD:FRAMe3:FLD3:DMIN 01100
Defines the parameter by using the index <m> for the frame number and <n> for
the field number. For an overview, see Table 24-15.
●
SEARch:TRIGger:USBPD:DMIN "Control", "MsgID", 01100
Defines the parameter by using the frame and field name.
SEARch:TRIGger:USBPd:ERENable............................................................................. 2232
SEARch:TRIGger:USBPd:ERRor<m>:ENABle................................................................2232
SEARch:TRIGger:USBPd:FRENable............................................................................. 2233
SEARch:TRIGger:USBPd:FRAMe<m>:ENABle...............................................................2233
SEARch:TRIGger:USBPd:FIENable...............................................................................2233
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:ENABle..................................................2233
SEARch:TRIGger:USBPd:BIT....................................................................................... 2234
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:BIT........................................................ 2234
SEARch:TRIGger:USBPd:DMAX...................................................................................2234
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:DMAX....................................................2234
SEARch:TRIGger:USBPd:DMIN....................................................................................2235
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:DMIN.....................................................2235
SEARch:TRIGger:USBPd:DOPerator.............................................................................2235
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:DOPerator..............................................2235
SEARch:TRIGger:USBPd:IMAX.................................................................................... 2236
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:IMAX..................................................... 2236
SEARch:TRIGger:USBPd:IMIN..................................................................................... 2236
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:IMIN...................................................... 2236
SEARch:TRIGger:USBPd:IOPerator.............................................................................. 2237
SEARch:TRIGger:USBPd:FRAMe<m>:FLD<n>:IOPerator............................................... 2237
SEARch:TRIGger:USBPd:ERENable <SearchName>,<ErrorName>, <Enabler>
SEARch:TRIGger:USBPd:ERRor<m>:ENABle <SearchName>,<Enable>
SEARch:TRIGger:USBPd:ERRor<m>:ENABle? <SearchName>
Enables or disables the checking condition for searching a specific error in the selected
field of the selected frame.
Protocols