R&S RTO6 - Page 1467

Remote control commands
R&S
®
RTO6
1467User Manual 1801.6687.02 ─ 05
<Source> C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2 |
C3W3 | C4W1 | C4W2 | C4W3
| M1 | M2 |
M3 | M4 | M5 | M6 |
M7 | M8 | R1 | R2 | R3 | R4 | TRK1 | TRK2 | TRK3 | TRK4 |
TRK5 | TRK6 | TRK7 | TRK8 | SG1TL1 | SG1TL2 | SG2TL1 |
SG2TL2 | SG3TL1 | SG3TL2 | SG4TL1 | SG4TL2 | SG5TL1 |
SG5TL2 | SG6TL1 | SG6TL2 | SG7TL1 | SG7TL2 | SG8TL1 |
SG8TL2 | Z1V1 | Z1V2 | Z1V3 | Z1V4 | Z1I1 | Z1I2 | Z1I3 | Z1I4 |
Z2V1 | Z2V2 | Z2V3 | Z2V4 | Z2I1 | Z2I2 | Z2I3 | Z2I4 | DIFF1 |
DIFF2 | COMMON1 | COMMON2
Waveform to be added, see Chapter 24.4.2, "Waveform parame-
ter", on page 1284
<XSource> ON | OFF
If on, the added waveform is assigned to the x-axis.
If of
f, it is assigned to the y-axis.
Usage: Setting only
Asynchronous command
WAVeform<m>:XYCurve:XSOurce <XSource>
Defines the signal source that supplies the x-values of the XY-diagram.
Suffix:
<m>
.
1..4
XY-diagram
Parameters:
<XSource>
C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2 |
C3W3 | C4W1 | C4W2 | C4W3 | M1 | M2 |
M3 | M4 | M5 | M6 |
M7 | M8 | R1 | R2 | R3 | R4 | SG1TL1 | SG1TL2 | SG2TL1 |
SG2TL2 | SG3TL1 | SG3TL2 | SG4TL1 | SG5TL1 | SG5TL2 |
SG6TL1 | SG6TL2 | SG7TL1 | SG7TL2 | SG8TL1 | SG8TL2 |
SG4TL2 | Z1V1 | Z1V2 | Z1V3 | Z1V4 | Z1I1 | Z1I2 | Z1I3 | Z1I4 |
Z2V1 | Z2V2 | Z2V3 | Z2V4 | Z2I1 | Z2I2 | Z2I3 | Z2I4 | DIFF1 |
DIFF2 | COMMON1 | COMMON2
Source of x-values, see Chapter 24.4.2, "Waveform parameter",
on page 1284
*RST: C1W1
Usage: Asynchronous command
WAVeform<m>:XYCurve:YSOurce <YSource>
Defines the signal source that supplies the y-values of the XY-diagram.
Suffix:
<m>
.
1..4
XY-diagram
Waveform analysis