Remote control commands
R&S
®
RTO6
1311User Manual 1801.6687.02 ─ 05
Parameters for setting and query:
<Source> C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2 |
C3W3 | C4W1 | C4W2 | C4W3
| M1 | M2 |
M3 | M4 | M5 | M6 |
M7 | M8 | R1 | R2 | R3 | R4 | XY1 | XY2 | XY3 | XY4 |
MRESult1 | MRESult2 | MRESult3 | MRESult4 | MRESult5 |
MRESult6 | MRESult7 | MRESult8 | SBUS1 | SBUS2 | SBUS3 |
SBUS4 | D0 | D1 | D2 | D3 | D4 | D5 | D6 | D7 | D8 | D9 | D10 |
D11 | D12 | D13 | D14 | D15 | MSOB1 | MSOB2 | MSOB3 |
MSOB4 | TRK1 | TRK2 | TRK3 | TRK4 | TRK5 | TRK6 | TRK7 |
TRK8 | Z1V1 | Z1V2 | Z1V3 | Z1V4 | Z1I1 | Z1I2 | Z1I3 | Z1I4 |
Z2V1 | Z2V2 | Z2V3 | Z2V4 | Z2I1 | Z2I2 | Z2I3 | Z2I4 | DIFF1 |
DIFF2 | COMMON1 | COMMON2 | BATHtub1 | BMEas1 |
SRESponse1 | SRHist1 | SDHist1 | TJHist1 | DJHist1 |
DDJHist1 | PJHist1 | RJOHist1 | SRTRack1 | SDTRack1 |
TJTRack1 | DJTRack1 | DDJTrack1 | PJTRack1 | RJOTrack1 |
TJSPectrum1 | DDJSpectrum1 | PJSPectrum1 |
RJOSpectrum1 | SEYE1 | BATHtub2 | BMEas2 | SRESponse2 |
SRHist2 | SDHist2 | TJHist2 | DJHist2 | DDJHist2 | PJHist2 |
RJOHist2 | SRTRack2 | SDTRack2 | TJTRack2 | DJTRack2 |
DDJTrack2 | PJTRack2 | RJOTrack2 | TJSPectrum2 |
DDJSpectrum2 | PJSPectrum2 | RJOSpectrum2 | SEYE2 |
NBAThtub1 | NBMeas1 | TNHist1 | DNHist1 | DDNHist1 |
PNHist1 | RNOHist1 | TNTRack1 | DNTRack1 | DDNTrack1 |
PNTRack1 | RNOTrack1 | TNSPectrum1 | DDNSpectrum1 |
PNSPectrum1 | RNOSpectrum1 | NBAThtub2 | NBMeas2 |
TNHist2 | DNHist2 | DDNHist2 | PNHist2 | RNOHist2 |
TNTRack2 | DNTRack2 | DDNTrack2 | PNTRack2 |
RNOTrack2 | TNSPectrum2 | DDNSpectrum2 | PNSPectrum2 |
RNOSpectrum2 | PJDHist1 | BUJHist1 | RJOHist1 | PJDTrack1 |
PJDSpectrum1 | PJDHist2 | BUJHist2 | RJOHist2 | PJDTrack2 |
PJDSpectrum2 | PNDHist1 | BUNHist1 | RNOHist1 |
PNDTrack1 | PNDSpectrum1 | PNDHist2 | BUNHist2 |
RNOHist2 | PNDTrack2 | PNDSpectrum2
Usage: Asynchronous command
DISPlay:SIGNal:LABel:STATe <LabelID>, <Source>, <State>
DISPlay:SIGNal:LABel:ST
A
Te? <LabelID>, <Source>
Displays or hides a single label that is identified by the signal source and label ID.
Parameters:
<State> OFF | ON
ON: shows the label on the screen.
DISPlay:SIGNal:LABel:
SHOW must be set to ON for the
source.
Parameters for setting and query:
<LabelID> String with the label identifier.
<Source> See DISPlay:SIGNal:
LABel:ADD.
Instrument setup
To Next Page
Loading...
