Remote control commands
R&S
®
RTO6
1650User Manual 1801.6687.02 ─ 05
Parameters:
<Source> | C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2
| C3W3 | C4W1 | C4W2 | C4W3
| M1 |
M2 | M3 | M4 | M5 | M6 |
M7 | M8 | R1 | R2 | R3 | R4 | D0 | D1 | D2 | D3 | D4 | D5 | D6 |
D7 | D8 | D9 | D10 | D11 | D12 | D13 | D14 | D15 | MSOB1 |
MSOB2 | MSOB3 | MSOB4 | TRK1 | TRK2 | TRK3 | TRK4 |
TRK5 | TRK6 | TRK7 | TRK8 | Z1V1 | Z1V2 | Z1V3 | Z1V4 |
Z1I1 | Z1I2 | Z1I3 | Z1I4 | Z2V1 | Z2V2 | Z2V3 | Z2V4 | Z2I1 |
Z2I2 | Z2I3 | Z2I4 | DIFF1 | DIFF2 | COMMON1 | COMMON2 |
BATHtub1 | BMEas1 | SRESponse1 | SRHist1 | SDHist1 |
TJHist1 | DJHist1 | DDJHist1 | PJHist1 | RJOHist1 | SRTRack1 |
SDTRack1 | TJTRack1 | DJTRack1 | DDJTrack1 | PJTRack1 |
RJOTrack1 | TJSPectrum1 | DDJSpectrum1 | PJSPectrum1 |
RJOSpectrum1 | SEYE1 | BATHtub2 | BMEas2 | SRESponse2 |
SRHist2 | SDHist2 | TJHist2 | DJHist2 | DDJHist2 | PJHist2 |
RJOHist2 | SRTRack2 | SDTRack2 | TJTRack2 | DJTRack2 |
DDJTrack2 | PJTRack2 | RJOTrack2 | TJSPectrum2 |
DDJSpectrum2 | PJSPectrum2 | RJOSpectrum2 | SEYE2 |
NBAThtub1 | NBMeas1 | TNHist1 | DNHist1 | DDNHist1 |
PNHist1 | RNOHist1 | TNTRack1 | DNTRack1 | DDNTrack1 |
PNTRack1 | RNOTrack1 | TNSPectrum1 | DDNSpectrum1 |
PNSPectrum1 | RNOSpectrum1 | NBAThtub2 | NBMeas2 |
TNHist2 | DNHist2 | DDNHist2 | PNHist2 | RNOHist2 |
TNTRack2 | DNTRack2 | DDNTrack2 | PNTRack2 |
RNOTrack2 | TNSPectrum2 | DDNSpectrum2 | PNSPectrum2 |
RNOSpectrum2 | PJDHist1 | BUJHist1 | RJHist1 | PJDTrack1 |
PJDSpectrum1 | PJDHist2 | BUJHist2 | RJHist2 | PJDTrack2 |
PJDSpectrum2 | PNDHist1 | BUNHist1 | RNHist1 | PNDTrack1 |
PNDSpectrum1 | PNDHist2 | BUNHist2 | RNHist2 | PNDTrack2 |
PNDSpectrum2
*RST: C1W1
Example: See Chapter 24.3.5.2, "Exporting waveform data to file",
on page
1267
Usage: Asynchronous command
EXPort:W
AVeform:MULTichannel <MltChXpt>
Enables or disables the multichannel export.
If you enable the multichannel export, all active channels are included to the export
data. You can change the export state using the CHANnel<m>:
EXPortstate com-
mand.
If multichannel export is disabled, select the waveform to be exported using the
EXPort:WAVeform:SOURce command.
Note that CHANnel<m>[:WAVeform<n>]:DATA[:VALues]? returns the data of all
channels that are selected for export, no matter of the channel suffix.
Data management
To Next Page
Loading...
