Xerox DocuColor 12/DCCS50 User Manual

1/05
2-101
DocuColor 12/DCCS50
8-175 Tray 5 Registration Sensor On Jam RAP, 8-
Status Indicator RAPs
Reissue
8-175 Tray 5 Registration Sensor On Jam RAP
The Registration Sensor did not actuate with 562 - 1010 msec after the feed started from Tray
5.
Initial Actions
• Refer to BSD 8.8 and BSD 8.10 for the following procedure.
• Check for any obstructions in the paper path.
Procedure
Enter dC330 008-155 Registration Sensor. Press Start. The display is H.
YN
+5 VDC is measure between P/
J421A-11 o
n the IOT Drive and GND.
YN
Go to Fl
ag 5 on BS
D 8.8 and check the harness for a short circuit. If the harness is
good, replace the Registration Sensor (PL 2.15).
Replace the IOT Drive PWB (PL 9.2).
Cheat
the Front Door Interlock. Open the Drawer and block the Registration Sensor with a
sheet of
paper. Carefully close the drawer. Enter dC330 008-155 Registration Sensor and
press Start. The display is L.
YN
There is +5 VDC between P
/J421A-
12 and P/J421A-10 on the IOT Drive PWB.
YN
Go to Fl
ag 5 on BS
D 8.8 and check the harness for a short circuit. If the harness is
good, replace the IOT Drive PWB (PL 9.2).
Go to Flag 5 and Fla
g 6 on BSD 8.8 and check the harness for an open circuit. If the har-
ness is OK, replace the Registration Sensor (PL 2.15). I
f the problem continues, replace
the IOT Drive PWB (PL 9.2).
Enter dC330 008-054 Registration Motor. Pre
ss Start. The Registration Motor energizes.
YN
Go to the R
egi
stration Motor RAP.
Check/replace the following components until the problem is resolved. Replace any compo-
nents that are worn, broken, binding, or slipping.
• Registration Roller and Roller, Springs, and Bearings in the Registration Assembly (PL
2.15)
•
Gear in the Registration Assembly (PL 2.1
5)
• Check for burrs on the Upper Chute and Chute in the Registration Assembly (PL 2.15).
8-176 Tray 1 Registration Sensor On Jam RAP
The Registration Sensor did not actuate with 316 - 416 msec after the feed started from Tray 1.
Initial Actions
• Refer to BSD 8.8 and BSD 8.10 for the following procedure.
• Check for any obstructions in the paper path.
Procedure
Enter dC330 008-155 Registration Sensor. Press Start. The display is H.
YN
+5 VDC is measure between P/
J421A-11 o
n the IOT Drive and GND.
YN
Go to F
lag 5 on B
SD 8.8 and check the harness for a short circuit. If the harness is
good, replace the Registration Sensor (PL 2.15).
Replace the IOT Drive PWB (PL 9.2).
Cheat the Front Door Interlock. Open the Drawer and block t
he Registration Sensor with a
sheet of paper. Carefully close the drawer. dC330 008-155 Registration Sensor and press
Start. The display is L.
YN
There is +5 VDC between P
/J421A-12 an
d P/J421A-10 on the IOT Drive PWB.
YN
Go to F
lag 5 on B
SD 8.8 and check the harness for a short circuit. If the harness is
good, replace the IOT Drive PWB (PL 9.2).
Go to Flag 5 and Fl
ag 6 on BSD 8.8 and check the harness for an open circuit. If the har-
ness is OK, replace the Registration Sensor (PL 2.15
). If the problem continues, replace
the IOT Drive PWB (PL 9.2).
Enter dC330 008-054 Registration Motor. Pre
ss Start. The Registration Motor energizes.
YN
Go to the Regist
ra
tion Motor RAP.
Check/replace the following components until the problem is resolved. Replace any compo-
nents that are worn, broken, binding, or slipping.
• Registration Roller and Roller, Springs, and Bearings in the Registration Assembly (PL
2.15
)
• Gear in the Registration Assembly (PL 2.15)
• C
heck for burrs on the Upper Chute and Chute in the Registration Assembly (PL 2.15).

Xerox DocuColor 12/DCCS50 Specifications

General

Brand	Xerox
Model	DocuColor 12/DCCS50
Category	All in One Printer
Language	English