Xerox DocuColor 12/DCCS50 User Manual

1/05
2-202
DocuColor 12/DCCS50
11-273 Mail Box OCT Offset Fail RAP
Reissue
Status Indicator RAPs
11-273 Mail Box OCT Offset Fail RAP
The Control Logic determined that either the Offset Home Sensor or the Offset Position Sensor
did not detect the OCT position within 600msec. for three consecutive attempts.
Initial Actions
• Refer to BSD11.7 for the following procedure.
• Ensure that connectors P/J564 on t
he Mail Box Control PWB, Shorting Plug P/J801A,
Double Plug J880, P/J803 on the Offset Motor, P/J806 on the Offset Position Sensor,
and P/J806 on the Offset Home Sensor are seated correctly and there are no obvious
crimped or broken wires.
Procedure
Manually move the Offset Catch Tray to the front/home position. Enter dC330 011-273 Offset
Home Sensor. The display indicates H.
YN
Remove the Offset Catch Tray from the machine. leave the Offset Catch Tray electrically
connec
te
d. Open the Offset Catch Tray to expose the motor and sensors.
Enter d
C330 011-273 Offset Home Sensor. Pre
ss Start. Block the Offset Home sensor
with a sheet of paper. The display indicates H.
YN
+5 VDC is measured between P/
J564-7
on the Mail Box Control PWB and GND
YN
Go to F
lag 3 on BSD 11.7. Check the wire for a short circuit to ground. If the
wire is good,
replace the Offset Home Sensor (PL 14.1).
Replace the Mail Box Control PWB (PL 13.10).
Ensure that the sensor actuator is properly in
stalled, and not bent or distorted. If the prob-
lem continues, replace the Offset Home Sensor (PL 14
.1).
Manually move the Offset Catch Tray to the rear/offset position. The display changes to L.
YN
+5 VDC is measured between P/
J5
64-7 and GND.
YN
Replace the Mail Box Control PWB (PL 13.10).
Disconnect P/J56
4 form the Mail Box Control PWB. +5 VDC is measured between P/
J564-4 and GND.
YN
Replace the Mail Box Control PWB (PL 13.10).
Go to Flag 2, Fl
ag
3, and Flag 5 on BSD 11.7. Check the wires for an open circuit. If the
wires are good, replace the Offset Home Sensor (PL 14.1).
Enter dC330 011-274 Offset Position Sensor. Th
e display indicates H.
YN
Remove the Offset Catch Tray from the machine. leave the Offset Catch Tray electrically
connec
te
d. Open the Offset Catch Tray to expose the motor and sensors.
Enter d
C330 011-274 Offset Position Sensor. Press Sta
rt. Block the Offset Home sen-
sor with a sheet of paper. The display indicates H.
YN
+5 VDC is measured between P/
J564-6 o
n the Mail Box Control PWB and GND
YN
Go to F
lag 4 on BSD 11.7. Check the wire for a short circuit to ground. If the
wi
re is good, replace the Offset Position Sensor (PL 14.1).
Replace the Mail Box Control PWB (PL 13.10).
Ensu
re that the sensor actuator is properly installed, and not bent or distorted. If the prob-
lem continues, replace the Off
set Position Sensor (PL 14.1).
Manually move the Offset Catch Tray to the front/home position. The display changes to L.
YN
+5 VDC is measured between P/
J564-6 and
GND.
YN
Replace the Mail Box Control PWB (PL 13.
10).
Di
sconnect P/J564 f
rom the Mail Box Control PWB. +5 VDC is measured between P/
J564-4 and GND.
YN
Replace the Mail Box Control PWB (PL 13.
10).
Go to
Flag 2, Fl
ag 4 on BSD 11.7, and Flag 5 on BSD 11.7. Check the wires for an open
circuit. If the wires are good, replace the Offset Position Sensor (PL 14.1).
Enter dC330 011-095 OCT Offset Motor Rear On. Pr
ess Start. The Offset Catch Tray
moves to the rear/offset position.
YN
Press St
op. Le
ss than +1 VDC is measured between P/J564-1 and P/J564-2
YN
Replace the Mail Box Control PWB (PL 13.
10).
Ente
r dC330 011-095 OCT Offset Motor Rear On. Pr
ess Start. +24 VDC is measured
between P/J564-1 and P/J564-2
YN
Disconnect P/
J564 f
rom the Mail Box Control PWB. Press Stop. Press Start. +24
VDC is measured between P/J564-1 and P/J564-2
YN
Replace the Mail Box Control PWB (PL 13.
10).
Go to
Flag 2 on BS
D 11.7. Check the wires for a short circuit to ground. If the wires
are good, replace the Offset Motor (PL 14.1).
Go to Flag 2 on BSD 1
1.7. Check the wires for an open circuit. If the wires are good,
replace the Offset Motor (PL 14.1).
Enter dC330 011-093 OCT Offset Motor Front On. Pre
ss Start. The Offset Catch Tray
moves to the front/home position.
YN
Replace the Mail Box Control PWB (PL 13.
10).
A
A
B
manuals4you.commanuals4you.com

Xerox DocuColor 12/DCCS50 Specifications

General

Brand	Xerox
Model	DocuColor 12/DCCS50
Category	All in One Printer
Language	English