Xerox DocuColor 12/DCCS50 User Manual

1/05
2-188
DocuColor 12/DCCS50
11-109 OCT Exit Sensor On Jam Short RAP
Reissue
Status Indicator RAPs
Replace the Mail Box Drive Motor (PL 13.10).
Ensure that the Mail Box Drive Motor Pulley is fastened to the motor shaft.
• Check the Drive Belt Tension Roll for proper tension.
• Check the Drive Belt for Damage
• Check that the gear pulleys are properly fastened to the drive rolls
Check the following parts for wear, glazing, or slipping.
• Entrance Roll (P
L 1
3.9)
• Pinch Rollers (PL 13.9)
• E
xit Roll (PL 13.9)
• Drive Belt (PL 13.10
)
Check the Drive Belt Tension Roll for proper tension.
The OCT Gate is in the Up or OCT position
YN
Enter dC330 011-081 OCT Gate Solenoid OCT On. Pr
ess Start. The OCT Gate
Solenoid energized.
YN
+24 VDC is measured between P/
J562-2 and
P/J562-1 on the Mail Box
Control PWB.
YN
+24 VDC is Measured between P/
J562-2
Mail Box Control PWB and
GND
YN
+24 VDC is measured between P
/J563-
1 on the Mail Box Control
PWB and GND.
YN
Go to the +24 VDC Wirenet and troubleshoot the wire between
P/
J563-1 on t
he Mail Box Control PWB and P/J45-6 on the Dis-
tribution PWB
Replace the Mail Box Control PWB (PL 13.
10)
L
ess than +1 VDC is measured between P/J562
-1 and GND
YN
Replace the Mail Box Control PWB (PL 13.
10)
Go
to Flag 5 on BSD 11.4. Check the wires for an open circuit. If the wires
are good, replace t
he OCT Gate Solenoid (PL 13.9).
Go to Flag 5 on
BSD 11.4. Check the wires for an open circuit. If the wires are
good, ensure that the OCT gate is connected to the OCT Gate Solenoid and
that it moves freely. If the problem continues replace the OCT Gate (PL 13.9)
and the OCT Gate Solenoid (PL 13.9).
Ensure that the OCT gate is connected to the OCT Gate Solenoid and that it moves
f
reely
. If the problem continues replace the OCT Gate (PL 13.9) and the OCT Gate
Solenoid (PL 13.9).
• Check the paper path for any obstructions that
could cause the paper to enter the
Vertical Transport.
• Ensure that the OCT gate moves freely. If the problem continues replace the OCT
Gate
(PL 13.9) and the OCT Gate Solenoid (PL 13.9).
Enter dC330 011-107 OCT Exit Sensor. Manually actuat
e the OCT Exit Sensor actuator. The
display changes from L to H to L as the actuator moves in and out of the sensor.
YN
The display is always H
YN
Go to F
lag 1on BSD 11.4. Check the harness for a short circ
uit to ground. If the har-
ness is good, replace the Oct Exit Sensor (PL 13.9).
+5 VDC
is measured between P/J562
-4 and P/J562-6
YN
CR1 on the Mail Box Control PWB is on.
YN
Go to the +5 VDC wirenet and troubleshoot the wires between P/
J5
69-1 and P/
J44-6 on the Distribution PWB.
Replace the Mail Box Control PWB (PL 13.10).
Go t
o Flag 2 and Flag 4 on BS
D11.4. Check the harness for an open circuit. If the harness
is good, replace the Oct Exit Sensor (PL 13.9).
With paper at the sensor, less than +1 VDC is measured between P/J56
2-5 and GND.
YN
Replace the OCT Exit Sensor (PL 13.
9).
Check
the following parts for wear, glazing, or slipping.
• Entrance Roll (PL 13.9)
•
Pinch Rollers (PL 13.9
)
•Exit Roll (PL 13.9)
•
Drive Belt (PL 1
3.10)
Check the Drive Belt Tension Roll for proper tension.
A
A
AB C D E F
G
G
H
H
manuals4you.commanuals4you.com

Xerox DocuColor 12/DCCS50 Specifications

General

Brand	Xerox
Model	DocuColor 12/DCCS50
Category	All in One Printer
Language	English