1/05
6-113
DocuColor 12/DCCS50
dC330 Component Control
General Procedures
Reissue
012-030 END WALL MOTOR
OPEN
Output High: On
Drives End Wall to open it (300ms)
Finisher
012-031 END WALL MOTOR
CLOSE
Out
put High: On
Drives End Wall to close it (300ms)
Finisher
012-036 COMPILER TRAY
SOLEN
OID
Output Low: On
Lowers Compiler Tray.
Finisher
012-040 STACKER MOTOR UP Output High: On
No output is allowed if a response
is sensed f
rom Tray Upper Limit
SNR before or while Stacker Tray
being driven upward. (500ms)
Finisher
012-041 STACKER MOTOR
DOW
N
Ou
tput High: On
No output is allowed if a response
is sensed f
rom Tray Upper Limit
SNR before or while Stacker Tray
being driven downward.
Finisher
012-053 EJECT PADDLE
MO
TO
R
Output High: On
Drives Set Clamp. (300ms)
Finisher
012-060 TAMPER MOTOR LOW
FRONT
Ou
tput Not measurable
Drives Tamper to front at a low
speed.
(560pps) (100 pulses)
Note: Not measurable in field due to
24V
Clock.
F
inisher
012-061 TAMPER MOTOR TOP
FR
ONT
Ou
tput Not measurable
Drives Tamper to front at a high
speed.
(2000pps) (100 pulses)
Note: Not measurable in field due to
24V
Clock.
F
inisher
012-062 TAMPER MOTOR LOW
RE
AR
Ou
tput Not measurable
Drives Tamper to rear at a low
speed.
(560pps) (100 pulses)
Note: Not measurable in field due to
24V
Clock.
F
inisher
012-063 TAMPER MOTOR TOP
RE
AR
Ou
tput Not measurable
Drives Tamper to rear at a high
speed.
(2000pps) (100 pulses)
Note: Not measurable in field due to
24V
Clock.
F
inisher
012-064 TAMPER MOTOR MID-
DLE FRONT
Output Not measurable
Drives Tamper to front at a medium
sp
eed.
(1000pps) (100 pulses)
Note: Not measurable in field due to
24V
Clock.
F
inisher
Table 2 Output Component Control Codes
ID
Des
cription In_Out Smart Help
Module_I
D
012-065 TAMPER MOTOR MID-
DLE REAR
Output Not measurable
Drives Tamper to rear at a medium
speed.
(1000pps) (100 pulses)
Note: Not measurable in field due to
24V
Clock
.
Finisher
012-070 FIN GATE SOLENOID-
MBX/SCT POSITION
Output Low: On
Switches Gate for MBX/SCT. (100
pul
ses)
F
inisher
012-071 FIN GATE SOLENOID-
F
INS
HER POSITION
Output Low: On
Switches Gate for Finisher. (100
pulses)
F
inisher
012-075 STAPLER MOTOR
CLOS
E
Out
put High: On
Does stapling. (Compiler cover
Safe
ty ON) (Stops at Home or
times out in 500ms).
Finisher
012-076 STAPLE POSITION
M
OTO
R TOP FRONT
Output Not measurable
Drives Stapler Unit to front at a high
speed (2700pp
s). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Finisher
012-077 STAPLE POSITION
M
OTO
R LOW FRONT
Output Not measurable
Drives Stapler Unit to front at a low
speed (2000pp
s). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Note: Not measurable in field due to
24V
Clock
F
inisher
012-078 STAPLE POSITION
TOP R
EAR
Output Not measurable
Drives Stapler Unit to rear at a high
speed (2700pp
s). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Note: Not measurable in field due to
24V
Clock
F
inisher
012-079 STAPLE POSITION
MOTOR LOW
REAR
Output Not measurable
Drives Stapler Unit to rear at a low
speed (2000pp
s). If End Wall Open
Sensor doesn’t sense any, no out-
put is allowed. (250 pulses).
Note: Not measurable in field due to
24V
Clock
F
inisher
012-081 MBX GATE SOLE-
NOID CLOSE
Output Low: On
Switches MBX Gate for SCT.
(150ms)
Fi
nisher
Table 2 Output Component Control Codes
I
D Descri
ption In_Out Smart Help
Module_I
D
To Next Page
Loading...
Need help?
General
