Xerox DocuColor 12/DCCS50 User Manual

1/05
6-101
DocuColor 12/DCCS50
dC330 Component Control
General Procedures
Reissue
007-189 TRAY CLOSED
SWITCH
Input High: Drawer / Tray is closed
Low: Drawer / Tray is open.
Detects when the HCF paper
Dra
wer /
Tray is closed.
HCF
007-190 HCF FEED HOT LINE Input Signal from the IOT to initiate paper
feed f
rom the HCF. In run mode a
high to low transition on this signal
will cause the HCF to feed paper. In
the diagnostic mode, this signal has
no effect on the HCF.
HCF
007-301 #1 TRAY SENSOR Input High: Tray Inserted
Low: Tray out
Processor
007-308 HCF INTERLOCK
SW
IT
CH
Input High: HCF is docked
Low: HCF is not docked.
Detects that the HCF is properly
doc
ked to t
he IOT.
HCF
008-104 #1 PRE FEED SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-105 #1 FEED OUT SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-109 #2 PRE FEED SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-110 #2 FEED OUT SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-114 #3 PRE FEED SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-115 #3 FEED OUT SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-119 #4 PRE FEED SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-120 #4 FEED OUT SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-135 TRAY 5 FEED SEN-
SOR
Input High: Paper
Low: No Paper
Processor
008-150 TAKE AWAY SENSOR Input High: No Paper
Low: Paper
Processor
008-153 PRE REGI SENSOR Input High: No Paper
Low: Paper
Processor
008-155 REGI SENSOR Input High: No Paper
Low: Paper
Processor
Table 1 Input Component Control Codes
ID
Description In_Out Smart Help
Module_I
D
008-163 BEHIND REGI JAM
SENSOR
Input High: No Paper
Low: Paper
Processor
008-198 TRANSPERENCY
(OHP) 1
SENSOR
Input High: No Transparency
Low: Transparency
Processor
008-199 OHP 2 SENSOR Input High: No Transparency
Low: Transparency
Processor
008-221 #1 TRAY STACK
H
EIGH
T (LEVEL) SEN-
SOR
Input High: Light block
Low: Light reception
Processor
008-222 #2 TRAY STACK
H
EIGH
T (LEVEL) SEN-
SOR
Input High: Light block
Low: Light reception
Processor
008-223 #3 TRAY STACK
H
EIGH
T (LEVEL) SEN-
SOR
Input High: Light block
Low: Light reception
Processor
008-224 #4 TRAY STACK
H
EIGH
T (LEVEL) SEN-
SOR
Input High: Light block
Low: Light reception
Processor
008-226 #5 TRAY BYPASS)
ST
AC
K HEIGHT LEVEL
UP SENSOR
Input Run #5 (Bypass) Nudger Roll Sole-
noid Simultaneously.
High: Lift up state
Low: Lift down State
Processor
008-227 #5 TRAY (BYPASS)
ST
AC
K HEIGHT LEVEL
DOWN SENSOR
Input High: Lift Down State
Low: Lift Up State
Processor
008-231 #1 TRAY NO PAPER
SE
NSO
R
Input High: No Paper
Low: Paper
Processor
008-232 #2 TRAY NO PAPER
SENSO
R
Input High: No Paper
Low: Paper
Processor
008-233 #3 TRAY NO PAPER
SENSO
R
Input High: No Paper
Low: Paper
Processor
008-234 #4 TRAY NO PAPER
SENSO
R
Input High: No Paper
Low: Paper
Processor
008-236 TRAY 5 PA PER SEN-
SOR
Input High: No Paper
Low: Paper
Processor
008-240 #2 TRAY SIZE S/W 1 Input High: Switch on (soft data)
Cannot run with Tray 3 size switch
1,2,3,
4
Cannot run with Tray 4 size switch
1,
2,3,
4
Processor
Table 1 Input Component Control Codes
ID Descri
ption In_Out Smart Help
Module_I
D

Xerox DocuColor 12/DCCS50 Specifications

General

Brand	Xerox
Model	DocuColor 12/DCCS50
Category	All in One Printer
Language	English