Xerox DocuColor 12/DCCS50

1/05
6-104
DocuColor 12/DCCS50
dC330 Component Control
Reissue
General Procedures
011-282 BIN 2 FULL SENSOR Input High: Not Full
Low: Full
Checks Bin 3 full detection sensor
st
atus.
So
rter
011-283 BIN 3 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 3 full detection sensor
status
So
rter
011-284 BIN 4 FULL SENSOR Input High: Not full
Low: Full
Checks the Bin 4 full detection sen-
sor status
Sorter
011-285 BIN 5 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 5 full detection sensor
st
atus
So
rter
011-286 BIN 6 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 6 full detection sensor
status
So
rter
011-287 BIN 7 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 7 full detection sensor
st
atus
So
rter
011-288 BIN 8 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 8 full detection sensor
st
atus
So
rter
011-289 BIN 9 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 9 full detection sensor
status
So
rter
011-290 BIN 10 FULL SENSOR Input High: Not full
Low: Full
Checks Bin 10 full detection sensor
st
atus
So
rter
011-301 MAILBOX FRONT
COV
ER INT
ERLOCK
SWITCH
Input High: Open
Low: Close
Sorter
011-302 DECURLER FRONT
COV
ER INT
ERLOCK
SWITCH
Input High: Open
Low: Close
Checks the Front Cover B
Sorter
Table 1 Input Component Control Codes
ID
Des
cription In_Out Smart Help
Module_I
D
011-303 MBX DOCKING INTLK
SWITCHES
Input High: Docking
Low: Open
Checks the IOT docking
Sorter
012-107 SCT EXIT SENSOR Input High: Paper sensed
Low: No paper sensed
Senses Paper Ejected to SCT Tray
Finisher
012-115 VERTICAL SENSOR Input High: Paper detected
Low: No paper detected
Detects paper ejected to Bins 1-10
Finisher
012-120 COMPILER EXIT SEN-
SOR
Input High: Paper detected
Low: No paper detected
INTERRUPT TAMPER MOTOR
dr
iv
e starting signal, EJECT
CLAMP & OFFSET MOTOR drive
starting signal, STAPLER MOVE
MOTOR drive starting signal, COM-
PILER TRAY UP/DOWN SOLE-
NOID drive starting signal.
Finisher
012-142 MAILBOX ENTRANCE
SE
NSO
R
Input High: Paper detected
Low: No paper detected
Senses paper ejected to Mailbox
Finisher
012-145 DECURLER EXIT SEN-
SOR
Input High: Paper detected
Low: No paper detected
Senses paper ejected to Decurler
Ex
it
F
inisher
012-200 MACHINE EXIT SEN-
SOR
Input HOTLINE Finisher
012-210 STACKER FULL SEN-
SOR
Input High: Paper sensed
Low: Paper not Sensed
Senses STACKER TRAY full of
sm
al
l sized paper.
Finisher
012-212 STACKER FULL
(M
IXED
SET SENSOR
Input High: Paper sensed
Low: Paper not Sensed
Senses STACKER TRAY full of
large sized p
aper.
F
inisher
012-240 EJECT CLAMP SEN-
SOR
Input High: Sensed
Low: Not Sensed
Senses EJECT ROLL UP/DOWN
Posit
ion.
STAPLER MOVE MOTOR drive
s
tart
ing signal, END WALL OPEN/
CLOSE MOTOR drive-for-open
starting signal.
Finisher
Table 1 Input Component Control Codes
I
D Descri
ption In_Out Smart Help
Module_I
D
manuals4you.commanuals4you.com