Xerox DocuColor 12/DCCS50

1/05
6-105
DocuColor 12/DCCS50
dC330 Component Control
General Procedures
Reissue
012-241 EJECT CLAMP HOME
SENSOR
Input High: Not Sensed
Low: Sensed
Senses SET CLAMP HOME Posi-
tion. SET CLAMP MOTOR drive
st
opping signal.
Pr
ocessor
012-250 STACK HEIGHT SEN-
SOR
Input High: Not Sensed
Low: Sensed
STACKER TRAY drive stopping sig-
nal.
Finisher
012-252 COMPILER PAPER
SE
NSO
R
Input High: Paper sensed
Low: No paper sensed
Senses paper (un)available on
COM
PIL
ER TRAY.
Finisher
012-253 STACKER PAPER
SE
NSO
R
Input High: Paper sensed
Low: No paper Available
Senses paper (un)available on
ST
ACK
ER TRAY.
Finisher
012-259 STACKER UPPER
LI
MI
T SENSOR
Input High: Sensed
Low: Not Sensed
Senses STACKER TRAY up limit.
Finisher
012-260 STACKER LOWER
LI
MI
T SENSOR
Input High: Sensed
Low: Not Sensed
Senses STACKER TRAY down
limit.
Finisher
012-265 TAMPER HOME SEN-
SOR
Input High: Sensed
Low: Not Sensed
Senses INTERRUPT TAMPER
H
OM
E Position. TAMPER MOTOR
drive stopping signal.
Finisher
012-269 STAPLER FRONT
CORNE
R S
ENSOR
Input High: Sensed
Low: Not Sensed
Senses INTERRUPT FRONT COR-
NER Position. STAPLER MOVE
M
OT
OR drive stopping signal.
Finisher
012-270 END WALL OPEN
SE
NSO
R
Input High: Sensed
Low: Not Sensed
Senses End Wall open. Stapler
M
ove
Motor drive starting signal.
Finisher
Table 1 Input Component Control Codes
ID Des
cription In_Out Smart Help
Module_I
D
012-271 STAPLE HEAD HOME
SENSOR
Input High: Sensed
Low: Not Sensed
Senses Staple Head Home Posi-
tion. Stapler Motor stop signal
(h
ardware stop
s driving). Eject
Motor drive starting signal.
Finisher
012-272 LOW STAPLE SWITCH Input High: Sensed
Low: Not Sensed
Senses Low Staple status (40 or
less
st
aples remain).
Finisher
012-273 STAPLE READY SEN-
SOR
Input High: Not closed
Low: Closed
Senses a staple at front end of Sta-
ple Head.
Finisher
012-274 CARTRIDGE SET
SW
IT
CH
Input High: Sensed
Low: Not Sensed
Senses Staple Cartridge is properly
ins
talled.
F
inisher
012-275 SCT FULL SENSOR Input High: Tray not full
Low: Tray full
Senses SCT Tray full of paper.
Finisher
012-276 DEC CAM POSITION
SE
NSO
R
Input High: Reflector sensed
Low: Reflector not sensed
Checks Decurler Cam Position
S
ensor inputt
ing.
Finisher
012-277 OFFSET HOME SEN-
SOR
Input High: Not sensed
Low: Sensed
Senses Eject Roll Home Position.
E
ject
Clamp & Offset Motor drive
starting signal.
Finisher
012-278 STAPLE FRONT
S
TRA
IGHT SENSOR
Input High: Sensed
Low: Not Sensed
Interrupt Front Straight Position.
S
tapler
Move Motor drive stopping
signal.
Finisher
012-279 STAPLE REAR
S
TRA
IGHT SENSOR
Input High: Sensed
Low: Not Sensed
Senses Rear Straight Position. Sta-
pler Move Motor drive stopping sig-
nal.
Finisher
Table 1 Input Component Control Codes
I
D Descri
ption In_Out Smart Help
Module_I
D