1/05
6-107
DocuColor 12/DCCS50
dC330 Component Control
General Procedures
Reissue
004-007 MAIN MOTOR Output The Main Motor rotates at a fre-
quency of 2000.8 Hz
The PR and IVT are turned on
s
imult
aneously
IF you operate the Drum Motor and
t
he main M
otor at the same time,
then start one of them, the other
Motor will shut down. (This is
because they are both using the
same Hard signal)
Processor
004-009 FUSER MOTOR Output The fuser motor rotates with a fre-
quency of 1495.886 Hz.
Note: also used with V-TRA
Processor
004-021 DRUM MOTOR Output - The drum motor rotates with a
f
requency
of 1495.886 Hz.
- Drum Motor Gain sell, 2 (low)
- PR and IBT are turned on simul-
taneously
- If you operate the drum motor
and t
he ma
in motor at the same
time, then stop one of them, the
other motor will slow down. (This is
because they are both using the
same hard signal)
Processor
005-011 SET GATE SOLENOID
OP
EN
Out
put After 5 sec., turned OFF automati-
cally
DADF
005-012 SET GATE SOLENOID
CLOSE
Out
put After 5 sec., turned OFF automati-
cally
DADF
005-040 FEED MOTOR Output After 2 sec., turned OFF automati-
cally
DADF
005-055 BELT MOTOR CW Output The DADF Belt Motor forwards DADF
005-056 BELT MOTOR CCW Output Belt Motor (Normal rotation)
The DADF Belt Motor reverses
DADF
005-075 REGI GATE SOLE-
NOID
Output After 5 sec., turned OFF automati-
cally
DADF
005-081 EXIT MOTOR Output On: Rotates DADF
005-083 DOC READY Output Simultaneous Output item: (IISS
sh
eet abort
)
DADF
005-084 DOC SET LED Output On: L DADF
006-002 ITT EXPOSURE LEAP Output After 180 sec., Turns OFF automat-
ically
IIT
Table 2 Output Component Control Codes
ID Des
cription In_Out Smart Help
Module_I
D
006-003 COOLING FAN LOW
SPEED
Output ON: L
Cooling Fan: High
IIT
006-005 IIT SCAN MOTOR
(Scan)
Out
put Moves the Carriage 50mm in the
scan direction and stops automati-
cally
IIT
006-006 IIT SCAN MOTOR
(Ret
urn)
Out
put IIT Scan Motor (Return) IIT
006-007 FUSER CUT Output On: Active IIT
006-013 COOLING FAN HIGH
SPEED
O
utput On: L IIT
006-086 IIT IMAGE AREA Output On: Active IIT
006-091 EXCHANGE TO ADF Output On: Active
Simultaneous on item
IIT
007-078 HCF FEED CLUTCH Output Engages the HCF Nudger Roll to
the Feed
Motor.
HCF
007-079 HCF ELEVATE MOTOR Output Unidirectional Motor to move the
HFC Paper
Tray in the up direction
only (motor is not engaged in the
down direction).
HCF
007-080 HCF FEED MOTOR Output Unipolar 200 step / rev stepper
m
ot
or with a maximum 800 PPS.
One revolution = 200 steps = 152
mm paper travel.
HCF
008-006 #1 NUDGER ROLL
SO
LEN
OID
Output ON time is 2000 msec Processor
008-007 #1 FEED MOTOR CCW Output Motor reverse. Tray lift up (upper
limit detect
ion stop)
ON time: 5500 msec
Processor
008-008 #1 FEED MOTOR CW Output Motor normal rotation: Feed Roll
ro
ta
tion
Processor
008-009 #1 TAKE AWAY FEED
CLUTCH
Out
put On drives connection Processor
008-011 #2 NUDGER ROLL
SOLEN
OID
Output ON time is 2000 msec Processor
008-012 #2 FEED MOTOR CCW Output Motor reverse: Tray lift up (upper
limit detect
ion stop)
Does not turn on if the tray is not
se
t
ON
time: 6000 msec
Processor
Table 2 Output Component Control Codes
ID Descri
ption In_Out Smart Help
Module_I
D
To Next Page
Loading...
Need help?
General
