1/05
6-108
DocuColor 12/DCCS50
dC330 Component Control
Reissue
General Procedures
008-013 #2 FEED MOTOR CW Output Motor normal rotation: Feed Roll
rotation
Processor
008-014 #2 TAKE AWAY FEED
CLUTCH
Out
put On drives connection Processor
008-016 #3 NUDGER ROLL
SOLEN
OID
Output ON time is 2000 msec Processor
008-017 #3 FEED MOTOR CCW Output Motor reverse: Tray lift up (upper
limit detection
stop)
Does not turn on if the tray is not
se
t.
O
N time: 6000 msec
Processor
008-018 #3 FEED MOTOR CW Output Motor normal rotation: Feed roll
rot
at
ion
Processor
008-019 #3 TAKE AWAY FEED
CLUTCH
Out
put On drives connection Processor
008-021 #4 NUDGER ROLL
SOLEN
OID
Output ON time is 2000 msec Processor
008-022 #4 FEED MOTOR CCW Output Motor reverse: Tray lift up (upper
limit detection
stop)
Does not turn on if the tray is not
se
t
ON
time: 6000 msec
Processor
008-023 #4 FEED MOTOR CW Output Motor normal rotation: Feed Roll
rot
at
ion
Processor
008-024 #4 TAKE AWAY FEED
CLUTCH
Out
put On drives connection Processor
008-025 TAKE AWAY MOTOR Output On (rotation) Processor
008-030 Tray 5 NUDGER ROLL
SOLEN
OID
Output x Processor
008-037 TRAY 5 FEED CLUTCH Output On drives connection Processor
008-049 TRAY 5 LIFTER
MOTOR
CCW (up)
Output x Processor
008-042 TRAY 5 LIFTER
MOTO
R CW (down)
Output Lower limit detection stop ON time:
300 msec
Tray 5 Lift Motor CCW
Processor
008-043 MAIN MOTOR 2 Output On: Port (L) Processor
008-054 REGI MOTOR Output On: Port (L) Processor
Table 2 Output Component Control Codes
ID
Des
cription In_Out Smart Help
Module_I
D
009-011 CARTRIDGE MOTOR K Output Automatically turns OFF after 10
sec.
Cannot run with Cartridge Motors Y
(0
09-012), M
(009-013), or C (009-
014)
Processor
009-012 CARTRIDGE MOTOR Y Output Automatically turns OFF after 10
se
c.
Cann
ot run with Cartridge Motors
M
(009-013),
C (009-014) or K
(009-011).
Processor
009-013 CARTRIDGE MOTOR
M
Output Automatically turns OFF after 10
se
c.
Cann
ot run with Cartridge Motors Y
(0
09-012),
C (009-014) or K (009-
011).
Processor
009-014 CARTRIDGE MOTOR
C
Output Automatically turns OFF after 10
se
c.
Cann
ot run with Cartridge Motors Y
(0
09-012),
C (009-013) or K (009-
011).
Processor
009-018 ROTARY LOCK MECH
LA
TC
H
Output Latch - High: Rotary Lock SEL
RETN
Low: Rotary Lock SEL SUCF
Release - High: Rotary Lock SEL
RE
TN
P
rocessor
009-021 DEVE MOTOR
CLUT
CH
Out
put On (High): Latch
Off (Low): Release
Processor
009-025 IBT ROLL CONTACT Output Run simultaneously with Main
Motor
(004-007)
Automatically turns OFF after the
Roll Ret
rac
t Home Position Sensor
detects the Contact Position (On:
Low, Off: High)
Processor
009-026 IBT ROLL RETRACT Output Run simultaneously with Main
M
otor
(004-007)
Automatically turns OFF after the
Roll Ret
rac
t Home Position Sensor
detects the Retract Position (On:
Low, Off: High)
Processor
009-031 DISPENSE MOTOR K Output Start after moving the Rotary to the
K
c
olor and dispensing the toner.
NOTE: To drive the rotary, Move the
ro
ta
ry to the K color in dC920
(Developer Unit Check).
Processor
Table 2 Output Component Control Codes
ID Descri
ption In_Out Smart Help
Module_I
D
manuals4you.commanuals4you.com
To Next Page
Loading...
Need help?
General
