Juniper ACX2000 - Page 18

Impact of Client-Side PCE Implementation on Network
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706
Configuring PCEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707
Example: Configuring the Path Computation Element Protocol for MPLS
RSVP-TE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707
Example: Configuring Path Computation Element Protocol for MPLS
RSVP-TE with Support of PCE-Initiated LSPs . . . . . . . . . . . . . . . . . . . . . 721
Configuring Path Computation Element Protocol for MPLS RSVP-TE with
Support of PCE-Initiated LSPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732
Example: Configuring Path Computation Element Protocol for MPLS
RSVP-TE with Support for PCE-Controlled Point-to-Multipoint
LSPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735
Part 6 Configuring Layer 2 and Layer 3 Features on ACX Series Routers
Chapter 24 Configuring Layer 2 Bridging and Q-in-Q Tunneling . . . . . . . . . . . . . . . . . . . 755
Layer 2 Bridge Domains on ACX Series Overview . . . . . . . . . . . . . . . . . . . . . . . . . 755
Layer 2 Learning and Forwarding for Bridge Domains Overview . . . . . . . . . . . . . 759
Configuring a Bridge Domain on ACX Series Routers . . . . . . . . . . . . . . . . . . . . . . 760
Configuring Integrated Routing and Bridging in ACX Series . . . . . . . . . . . . . . . . . 761
Configuring VLAN Identifiers for Bridge Domains in ACX Series . . . . . . . . . . . . . 764
Disabling MAC Learning for Bridge Domains on ACX Series . . . . . . . . . . . . . . . . . 765
Configuring Static MAC Addresses for Logical Interfaces in a Bridge Domain in
ACX Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
Configuring the Size of the MAC Address Table for Bridge Domains in ACX
Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
Configuring MAC Address Limits on a Logical Interface . . . . . . . . . . . . . . . . . . . . 767
Configuring MAC Address limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 768
Configuring MAC Address Limits for VLANs . . . . . . . . . . . . . . . . . . . . . . . . . 768
Configuring MAC Address Limits for VPLS . . . . . . . . . . . . . . . . . . . . . . . . . . . 768
CLI Commands to Configure MAC Address Limits . . . . . . . . . . . . . . . . . . . . 769
Preventing Communication Among Customer Edge Devices as ACX Routers . . 770
Q-in-Q Tunneling on ACX Series Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 770
Configuring Q-in-Q Tunneling on ACX Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 771
Chapter 25 Configuring Layer 2 and Layer 3 Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773
Configuring Interfaces for Layer 2 Circuits Overview . . . . . . . . . . . . . . . . . . . . . . . 774
Configuring the Address for the Neighbor of the Layer 2 Circuit . . . . . . . . . . . . . . 774
Configuring the Neighbor Interface for the Layer 2 Circuit . . . . . . . . . . . . . . . . . . 774
Configuring a Community for the Layer 2 Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . 775
Configuring the Control Word for Layer 2 Circuits . . . . . . . . . . . . . . . . . . . . . . . . . 775
Configuring the Encapsulation Type for the Layer 2 Circuit Neighbor Interface . . 777
Configuring the MTU Advertised for a Layer 2 Circuit . . . . . . . . . . . . . . . . . . . . . . 777
Configuring the Protect Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 778
Configuring the Virtual Circuit ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 778
Configuring the Interface Encapsulation Type for Layer 2 Circuits . . . . . . . . . . . . 779
Configuring Layer 2 Circuits over Both RSVP and LDP LSPs . . . . . . . . . . . . . . . . . 779
Enabling the Layer 2 Circuit When the MTU Does Not Match . . . . . . . . . . . . . . . 780
Copyright © 2017, Juniper Networks, Inc.xviii
ACX Series Universal Access Router Configuration Guide