Cisco Catalyst 2960 Series User Manual

Caller-ID = “408”
Acct-Status-Type = Stop
Acct-Authentic = RADIUS
Service-Type = Exec-User
Acct-Session-Id = “0000000D”
Acct-Delay-Time = 0
User-Id = “username1”
NAS-Identifier = “172.16.25.15”
The following example shows the information contained in a TACACS+ network accounting record for a
PPP user who first started an EXEC session:
Wed Jun 27 04:00:35 2001 172.16.25.15 username1 tty4 562/4327528 starttask_id=28
service=shell
Wed Jun 27 04:00:46 2001 172.16.25.15 username1 tty4 562/4327528 starttask_id=30
addr=10.1.1.1 service=ppp
Wed Jun 27 04:00:49 2001 172.16.25.15 username1 tty4 408/4327528 update
task_id=30 addr=10.1.1.1 service=ppp protocol=ip addr=10.1.1.1
Wed Jun 27 04:01:31 2001 172.16.25.15 username1 tty4 562/4327528 stoptask_id=30
addr=10.1.1.1 service=ppp protocol=ip addr=10.1.1.1 bytes_in=2844
bytes_out=1682 paks_in=36 paks_out=24 elapsed_time=51
Wed Jun 27 04:01:32 2001 172.16.25.15 username1 tty4 562/4327528 stoptask_id=28
service=shell elapsed_time=57
The precise format of accounting packets records may vary depending on the security server daemon.Note
The following example shows the information contained in a RADIUS network accounting record for a PPP
user who comes in through autoselect:
Wed Jun 27 04:30:52 2001
NAS-IP-Address = “172.16.25.15”
NAS-Port = 3
User-Name = “username1”
Client-Port-DNIS = “4327528”
Caller-ID = “562”
Acct-Status-Type = Start
Acct-Authentic = RADIUS
Service-Type = Framed
Acct-Session-Id = “0000000B”
Framed-Protocol = PPP
Acct-Delay-Time = 0
User-Id = “username1”
NAS-Identifier = “172.16.25.15”
Wed Jun 27 04:36:49 2001
NAS-IP-Address = “172.16.25.15”
NAS-Port = 3
User-Name = “username1”
Client-Port-DNIS = “4327528”
Caller-ID = “562”
Acct-Status-Type = Stop
Acct-Authentic = RADIUS
Service-Type = Framed
Acct-Session-Id = “0000000B”
Framed-Protocol = PPP
Framed-IP-Address = “10.1.1.1”
Acct-Input-Octets = 8630
Acct-Output-Octets = 5722
Acct-Input-Packets = 94
Acct-Output-Packets = 64
Acct-Session-Time = 357
Acct-Delay-Time = 0
User-Id = “username1”
NAS-Identifier = “172.16.25.15”
Consolidated Platform Configuration Guide, Cisco IOS Release 15.2(4)E (Catalyst 2960-X Switches)
1008
Information About Configuring Accounting

Cisco Catalyst 2960 Series Specifications

General

Layer	Layer 2
Power over Ethernet (PoE)	Available on some models
RAM	128 MB
Flash Memory	32 MB
MAC Address Table Size	8000
Operating Temperature	0°C to 45°C (32 to 113°F)
Ports	24 or 48 x 10/100/1000