Cisco Catalyst 2960 Series User Manual

Acct-Status-Type = Start
Acct-Authentic = RADIUS
Service-Type = Exec-User
Acct-Session-Id = “00000010”
Acct-Delay-Time = 0
User-Id = “username1”
NAS-Identifier = “172.16.25.15”
Wed Jun 27 04:48:46 2001
NAS-IP-Address = “172.16.25.15”
NAS-Port = 26
User-Name = “username1”
Caller-ID = “10.68.202.158”
Acct-Status-Type = Stop
Acct-Authentic = RADIUS
Service-Type = Exec-User
Acct-Session-Id = “00000010”
Acct-Session-Time = 14
Acct-Delay-Time = 0
User-Id = “username1”
NAS-Identifier = “172.16.25.15”
The following example shows the information contained in a TACACS+ EXEC accounting record for a Telnet
user:
Wed Jun 27 04:06:53 2001 172.16.25.15 username1 tty26 10.68.202.158
starttask_id=41 service=shell
Wed Jun 27 04:07:02 2001 172.16.25.15 username1 tty26 10.68.202.158
stoptask_id=41 service=shell elapsed_time=9
Command Accounting
Command accounting provides information about the EXEC shell commands for a specified privilege level
that are being executed on a network access server. Each command accounting record includes a list of the
commands executed for that privilege level, as well as the date and time each command was executed, and
the user who executed it.
The following example shows the information contained in a TACACS+ command accounting record for
privilege level 1:
Wed Jun 27 03:46:47 2001 172.16.25.15 username1 tty3 5622329430/4327528
stop task_id=3 service=shell priv-lvl=1 cmd=show version <cr>
Wed Jun 27 03:46:58 2001 172.16.25.15 username1 tty3 5622329430/4327528
stop task_id=4 service=shell priv-lvl=1 cmd=show interfaces Ethernet 0
<cr>
Wed Jun 27 03:47:03 2001 172.16.25.15 username1 tty3 5622329430/4327528
stop task_id=5 service=shell priv-lvl=1 cmd=show ip route <cr>
The following example shows the information contained in a TACACS+ command accounting record for
privilege level 15:
Wed Jun 27 03:47:17 2001 172.16.25.15 username1 tty3 5622329430/4327528
stop task_id=6 service=shell priv-lvl=15 cmd=configure terminal <cr>
Wed Jun 27 03:47:21 2001 172.16.25.15 username1 tty3 5622329430/4327528
stop task_id=7 service=shell priv-lvl=15 cmd=interface Serial 0 <cr>
Wed Jun 27 03:47:29 2001 172.16.25.15 username1 tty3 5622329430/4327528
stop task_id=8 service=shell priv-lvl=15 cmd=ip address 10.1.1.1 255.255.255.0
<cr>
The Cisco implementation of RADIUS does not support command accounting.Note
Consolidated Platform Configuration Guide, Cisco IOS Release 15.2(4)E (Catalyst 2960-X Switches)
1010
Information About Configuring Accounting

Cisco Catalyst 2960 Series Specifications

General

Layer	Layer 2
Power over Ethernet (PoE)	Available on some models
RAM	128 MB
Flash Memory	32 MB
MAC Address Table Size	8000
Operating Temperature	0°C to 45°C (32 to 113°F)
Ports	24 or 48 x 10/100/1000